VIPER12ADIP-E STMicroelectronics, VIPER12ADIP-E Datasheet - Page 10

IC OFFLINE SWIT PWM SMPS CM 8DIP

VIPER12ADIP-E

Manufacturer Part Number
VIPER12ADIP-E
Description
IC OFFLINE SWIT PWM SMPS CM 8DIP
Manufacturer
STMicroelectronics
Series
VIPER™r
Type
Pulse Width Modulator Controllerr
Datasheets

Specifications of VIPER12ADIP-E

Output Isolation
Isolated
Frequency Range
54 ~ 66kHz
Voltage - Input
8 ~ 50 V
Voltage - Output
730V
Power (watts)
8W
Operating Temperature
25°C ~ 125°C
Package / Case
8-DIP (0.300", 7.62mm)
Current, Supply
4.5 mA
Frequency, Oscillator
60 kHz
Package Type
DIP-8
Regulator Type
Switching
Resistance, Thermal, Junction To Case
15 °C/W
Temperature, Operating, Range
-40 to +150 °C
Time, Fall
100 ns
Time, Rise
50 ns
Voltage, Supply
18 V
Output Voltage
38 V
Output Power
5 W
Input Voltage
0 V to 50 V
Switching Frequency
60 KHz
Operating Temperature Range
- 40 C to + 150 C
Mounting Style
Through Hole
For Use With
497-6413 - BOARD EVAL VIPER12A LP AC/DC497-5084 - EVAL BOARD TRAVEL ADAPTOR 3.6W497-5082 - EVAL BOARD FLYBACK PWR SUPPLY 6W497-4932 - BOARD POWER SUPPLY 1.8W VIPER12A497-4931 - BOARD 6W DUAL OUTPUT VIPER12A497-4930 - BOARD 6W SINGLE OUTPUT VIPER12A
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-5575-5
VIPER12ADIP-E

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
VIPER12ADIP-E
Manufacturer:
ST
Quantity:
676 004
Part Number:
VIPER12ADIP-E
Manufacturer:
ST
Quantity:
1
Part Number:
VIPER12ADIP-E
Manufacturer:
ST
0
Part Number:
VIPER12ADIP-E
Manufacturer:
ST
Quantity:
2 500
Part Number:
VIPER12ADIP-E
Manufacturer:
ST
Quantity:
20 000
Part Number:
VIPER12ADIP-E
Manufacturer:
ST
Quantity:
15 611
Part Number:
VIPER12ADIP-E
Manufacturer:
STM
Quantity:
13 916
Part Number:
VIPER12ADIP-E
0
Company:
Part Number:
VIPER12ADIP-E
Quantity:
50 000
Company:
Part Number:
VIPER12ADIP-E
Quantity:
300 000
Company:
Part Number:
VIPER12ADIP-E
Quantity:
68 000
Part Number:
VIPER12ADIP-E==ST
Manufacturer:
ST
0
Feedback pin principle of operation
10/21
The current limitation is obtained with the FB pin shorted to ground (V
to a negative current sourced by this pin, and expressed by:
By reporting this expression in the previous one, it is possible to obtain the drain current
limitation I
In a real application, the FB pin is driven with an optocoupler as shown on
acts as a pull up. So, it is not possible to really short this pin to ground and the above drain
current value is not achievable. Nevertheless, the capacitor C is averaging the voltage on
the FB pin, and when the optocoupler is off (start up or short circuit), it can be assumed that
the corresponding voltage is very close to 0 V.
For low drain currents, the formula (1) is valid as long as IFB satisfies I
I
stop switching. This is represented on
the PWM COMPARATOR SECTION. Actually, as soon as the drain current is about 12 % of
Idlim, that is to say 50 mA, the device will enter a burst mode operation by missing switching
cycles. This is especially important when the converter is lightly loaded.
Figure 6.
It is then possible to build the total DC transfer function between I
Figure 6 on page
associated minimum turn on time. This imposes a minimum drain current under which the
device is no more able to control it in a linear way. This drain current depends on the primary
inductance value of the transformer and the input voltage. Two cases may occur, depending
on the value of this current versus the fixed 50 mA value, as described above.
FBsd
is an internal threshold of the VIPER12A. If I
Dlim
I
FB
:
transfer function
10. This figure also takes into account the internal blanking time and its
Doc ID 11977 Rev 2
I
Dlim
=
Figure 12 on page
G
I
FB
ID
=
0.23V
0.23V
--------------- -
R
1
FB
------ -
R
1
exceeds this threshold the device will
2
+
------ -
R
1
14, and I
1
D
FBsd
and I
FB
FB
value is specified in
FB
= 0 V). This leads
< I
Figure 5
as shown on
FBsd
VIPER12A-E
, where
which

Related parts for VIPER12ADIP-E