NCP1200P40 ON Semiconductor, NCP1200P40 Datasheet - Page 8
![IC CTRLR PWM CM 8DIP](/photos/7/33/73389/ncp1200p40_sml.jpg)
NCP1200P40
Manufacturer Part Number
NCP1200P40
Description
IC CTRLR PWM CM 8DIP
Manufacturer
ON Semiconductor
Datasheet
1.NCP1200P100G.pdf
(16 pages)
Specifications of NCP1200P40
Output Isolation
Isolated
Frequency Range
36 ~ 48kHz
Voltage - Input
11.4 ~ 16 V
Operating Temperature
-25°C ~ 150°C
Package / Case
8-DIP (0.300", 7.62mm)
Number Of Outputs
1
Duty Cycle (max)
80 %
Output Current
250 mA
Mounting Style
Through Hole
Switching Frequency
42 KHz
Operating Supply Voltage
16 V
Maximum Operating Temperature
+ 150 C
Fall Time
28 ns
Rise Time
67 ns
Synchronous Pin
No
Topology
Flyback, Forward
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
NCP1200P40OS
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NCP1200P40
Manufacturer:
SHARP
Quantity:
5 510
Company:
Part Number:
NCP1200P40G
Manufacturer:
ON Semiconductor
Quantity:
135
Company:
Part Number:
NCP1200P40G
Manufacturer:
ON
Quantity:
502
Part Number:
NCP1200P40G
Manufacturer:
ON/安森美
Quantity:
20 000
Skipping Cycle Mode
the output power demand drops below a given level. This is
accomplished by monitoring the FB pin. In normal
operation, pin 2 imposes a peak current accordingly to the
load value. If the load demand decreases, the internal loop
asks for less peak current. When this setpoint reaches a
determined level, the IC prevents the current from
decreasing further down and starts to blank the output
pulses: the IC enters the so−called skip cycle mode, also
named controlled burst operation. The power transfer now
depends upon the width of the pulse bunches (Figure 18 ).
Suppose we have the following component values:
Lp, primary inductance = 1 mH
F
Ip skip = 300 mA (or 350 mV / Rsense)
The theoretical power transfer is therefore:
10 ms over a recurrent period of 100 ms, then the total power
transfer is: 2.2 . 0.1 = 220 mW.
a look at the operation mode versus the FB level
immediately gives the necessary insight:
1
2
FB
SW
@ Lp @ Ip
The NCP1200 automatically skips switching cycles when
If this IC enters skip cycle mode with a bunch length of
To better understand how this skip cycle mode takes place,
3. Permanently force the V
, switching frequency = 48 kHz
an auxiliary winding. It will automatically
disconnect the internal startup source and the IC
will be fully self−supplied from this winding.
Again, the total power drawn from the mains will
significantly decrease. Make sure the auxiliary
voltage never exceeds the 16 V limit.
Figure 17. Feedback Voltage Variations
2
@ Fsw + 2.2 W
Normal Current Mode Operation
Ip
Skip Cycle Operation
min
= 350 mV / R
CC
sense
level above V
CCH
http://onsemi.com
with
4.8 V
3.8 V
1.4 V
8
default), the peak current cannot exceed 1 V/Rsense. When
the IC enters the skip cycle mode, the peak current cannot go
below Vpin1 / 4 (Figure 19). The user still has the flexibility
to alter this 1.4 V by either shunting pin 1 to ground through
a resistor or raising it through a resistor up to the desired
level.
When FB is above the skip cycle threshold (1.4 V by
Figure 19. The skip cycle takes place at low peak
currents which guarantees noise free operation
Figure 18. Output pulses at various power levels
Max Peak
Current
(X = 5 ms/div) P1<P2<P3
Skip Cycle
Current Limit
P1
P2
P3