LT1579CS8-3#PBF Linear Technology, LT1579CS8-3#PBF Datasheet - Page 13
![IC LDO REG SMART DUAL 3V 8-SOIC](/photos/6/62/66297/8-soic_05-08-1610_sml.jpg)
LT1579CS8-3#PBF
Manufacturer Part Number
LT1579CS8-3#PBF
Description
IC LDO REG SMART DUAL 3V 8-SOIC
Manufacturer
Linear Technology
Datasheet
1.LT1579CS-5.pdf
(20 pages)
Specifications of LT1579CS8-3#PBF
Function
Back-Up Management
Battery Type
Smart Batteries
Operating Temperature
0°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (0.154", 3.90mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIONS
A small capacitor placed in parallel with the top resistor
(R2) of the output divider is necessary for stability and
transient performance of the adjustable LT1579. The
impedance of C
of R1.
The adjustable LT1579 is tested and specified with the
output pin tied to the adjust pin and a 3 A load (unless
otherwise noted) for an output voltage of 1.5V. Specifica-
tions for output voltages greater than 1.5V are propor-
tional to the ratio of the desired output voltage to 1.5V;
(V
current change of 1mA to 300mA is – 2mV typical at
V
Output Capacitance and Transient Response
The LT1579 is designed to be stable with a wide range of
output capacitors. The ESR of the output capacitor affects
stability, most notably with small capacitors. A minimum
output capacitor of 4.7 F with an ESR of 3 or less is
recommended to prevent oscillations. Smaller value ca-
pacitors may be used, but capacitors which have a low
ESR (i.e. ceramics) may need a small series resistor added
to bring the ESR into the range suggested in Table 1. The
LT1579 is a micropower device and output transient
response is a function of output capacitance. Larger
values of output capacitance decrease the peak deviations
and provide improved output transient response for larger
load current changes. Bypass capacitors, used to decouple
individual components powered by the LT1579, will
increase the effective output capacitor value.
Table 1. Suggested ESR Range
OUT
OUT
1 5
12
OUTPUT CAPACITANCE
= 1.5V. At V
/1.5V). For example, load regulation for an output
.
V
V
–
1.5 F
2.2 F
3.3 F
4.7 F
2
mV
FB
OUT
at 10kHz should be less than the value
U
= 12V, load regulation is:
–
16
INFORMATION
mV
U
SUGGESTED ESR RANGE
W
0.5 to 3
0.2 to 3
1 to 3
0 to 3
U
BIASCOMP Pin Compensation
The BIASCOMP pin is a connection to a compensation
point for the internal bias circuitry. It must be bypassed
with a 0.01 F capacitor for stability during the switch from
V
“Hot” Plugging and Unplugging of Inputs
The LT1579 is designed to maintain regulation even if one
of the outputs is instantaneously removed. If the primary
input is supplying load current, removal and insertion of
the secondary input creates no noticeable transient at the
output. In this case, the LT1579 continues to supply
current from the primary; no switching is required. How-
ever, when load current is being supplied from the primary
input and it is removed, load current must be switched
from the primary to the secondary input. In this case, the
LT1579 sees the input capacitor as a rapidly discharging
battery. If it discharges too quickly, the LT1579 does not
have ample time to switch over without a large transient
occurring at the output. The input capacitor must be large
enough to supply load current during the transition from
primary to secondary input. Replacement of the primary
creates a smaller transient on the output because both
inputs are present during the transition. For a 100mA load,
input and output capacitors of 10 F will limit peak output
deviations to less than 50mV. See the “Hot” Plugging and
Unplugging Transient Response in the Typical Perfor-
mance Characteristics. Proportionally larger values for
input and output capacitors are needed to limit peak
deviations on the output when delivering larger load
currents.
Standby Mode
“Standby” mode is where one input draws a minimum
quiescent current when the other input is delivering all
bias and load currents . In this mode, the standby current
is the quiescent current drawn from the standby input. The
secondary input will be in standby mode, when the pri-
mary input is delivering all load and bias currents. When
the secondary input is in standby mode the current drawn
from the secondary input will be 3 A if V
IN1
to V
IN2
.
IN1
> V
LT1579
IN2
and 5 A
13