ADE7758ARWZ Analog Devices Inc, ADE7758ARWZ Datasheet - Page 35
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADE7758ARWZ
Manufacturer Part Number
ADE7758ARWZ
Description
IC ENERGY METERING 3PHASE 24SOIC
Manufacturer
Analog Devices Inc
Datasheet
1.ADE7758ARWZ.pdf
(72 pages)
Specifications of ADE7758ARWZ
Input Impedance
380 KOhm
Measurement Error
0.1%
Voltage - I/o High
2.4V
Voltage - I/o Low
0.8V
Current - Supply
8mA
Voltage - Supply
4.75 V ~ 5.25 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
24-SOIC (0.300", 7.50mm Width)
Meter Type
3 Phase
Ic Function
Poly Phase Multifunction Energy Metering IC
Supply Voltage Range
4.75V To 5.25V
Operating Temperature Range
-40°C To +85°C
Digital Ic Case Style
SOIC
No. Of Pins
24
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADE7758ARWZ
Manufacturer:
AD
Quantity:
517
Company:
Part Number:
ADE7758ARWZ
Manufacturer:
AD
Quantity:
53
Part Number:
ADE7758ARWZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
ADE7758ARWZRL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Phase A, Phase B, and Phase C zero crossings are, respectively,
included when counting the number of half-line cycles by
setting ZXSEL[0:2] bits (Bit 3 to Bit 5) in the LCYCMODE
register. Any combination of the zero crossings from all three
phases can be used for counting the zero crossing. Only one
phase should be selected at a time for inclusion in the zero
crossings count during calibration (see the Calibration section).
The number of zero crossings is specified by the LINECYC
register. LINECYC is an unsigned 16-bit register. The ADE7758
can accumulate active power for up to 65535 combined zero
crossings. Note that the internal zero-crossing counter is always
active. By setting the LWATT bit, the first energy accumulation
result is, therefore, incorrect. Writing to the LINECYC register
when the LWATT bit is set resets the zero-crossing counter, thus
ensuring that the first energy accumulation result is accurate.
At the end of an energy calibration cycle, the LENERGY bit
(Bit 12) in the STATUS register is set. If the corresponding
mask bit in the interrupt mask register is enabled, the IRQ
output also goes active low; thus, the IRQ can also be used to
signal the end of a calibration.
Because active power is integrated on an integer number of half-
line cycles in this mode, the sinusoidal component is reduced to
0, eliminating any ripple in the energy calculation. Therefore, total
energy accumulated using the line-cycle accumulation mode is
where t is the accumulation time.
Note that line cycle active energy accumulation uses the same
signal path as the active energy accumulation. The LSB size of
these two methods is equivalent. Using the line cycle accumula-
tion to calculate the kWh/LSB constant results in a value that
can be applied to the WATTHR registers when the line
accumulation mode is not selected (see the Calibration section).
REACTIVE POWER CALCULATION
A load that contains a reactive element (inductor or capacitor)
produces a phase difference between the applied ac voltage and
the resulting current. The power associated with reactive elements
is called reactive power, and its unit is VAR. Reactive power is
defined as the product of the voltage and current waveforms when
one of these signals is phase shifted by 90°.
E(t) = VRMS × IRMS × t
(26)
Rev. D | Page 35 of 72
Equation 30 gives an expression for the instantaneous reactive
power signal in an ac system when the phase of the current
channel is shifted by +90°.
where:
v = rms voltage.
i = rms current.
θ = total phase shift caused by the reactive elements in the load.
Then the instantaneous reactive power q(t) can be expressed as
where
Note that q(t) can be rewritten as
The average reactive power over an integral number of line
cycles (n) is given by the expression in Equation 31.
where:
T is the period of the line cycle.
Q is referred to as the average reactive power. The instantaneous
reactive power signal q(t) is generated by multiplying the
voltage signals and the 90° phase-shifted current in each phase.
The dc component of the instantaneous reactive power signal in
each phase (A, B, and C) is then extracted by a low-pass filter to
obtain the average reactive power information on each phase.
This process is illustrated in Figure 71. The reactive power of
each phase is accumulated in the corresponding 16-bit VAR-
hour register (AVARHR, BVARHR, or CVARHR). The input to
each reactive energy register can be changed depending on the
accumulation mode setting (see Table 21).
v
t i
i
q
q
q
Q
( )
′
( )
( )
( )
( )
( )
i ′
t
t
t
t
t
=
( )
=
t
=
=
=
=
=
nT
1
VI
VI
v
is the current waveform phase shifted by 90°.
2
( )
2
2
nT
t
∫
0
I
V
sin
cos
q
I
sin
( )
sin
×
t
sin
( )
⎛
⎜
⎝
θ
dt
( )
i
–
⎛
⎜
⎝
ωt
′
(
( )
ωt
ωt
θ
+
t
=
–
VI
V
–
+
π
2
θ
×
sin
π
2
⎞
⎟
⎠
)
I
⎞
⎟
⎠
–
(
×
2
VI
ωt
sin
cos
–
( )
θ
θ
⎛
⎜
⎝
)
2
ωt
–
θ
–
π
2
⎞
⎟
⎠
ADE7758
(27)
(28)
(29)
(30)
(31)