ADE7751AN Analog Devices Inc, ADE7751AN Datasheet - Page 15

• Manufacturer Part Number: ADE7751AN
• Description: IC ENERGY METERING DETEC 24-PDIP
• Manufacturer: Analog Devices Inc

Specifications of ADE7751AN

• Rohs Status: RoHS non-compliant
• Input Impedance: 390 KOhm
• Measurement Error: 0.1%
• Voltage - I/o High: 2.4V
• Voltage - I/o Low: 0.8V
• Current - Supply: 3mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 24-DIP (0.300", 7.62mm)
• Meter Type: Single Phase
• Lead Free Status / Rohs Status: Not Compliant

Example 1
If full-scale differential dc voltages of +660 mV and –660 mV are
applied to V1 and V2 respectively (660 mV is the maximum
differential voltage that can be connected to Channel 1 and
Channel 2), the expected output frequency is calculated as follows.
Gain
F
V1
V2
V
Note: If the on-chip reference is used, actual output frequencies
may vary from device to device due to reference tolerance of 8%.
Example 2
In this example, if ac voltages of 660 mV peak are applied to
V1 and V2, the expected output frequency is calculated as follows.
Gain
F
V1
V2
V
Note: If the on-chip reference is used, actual output frequencies
may vary from device to device due to reference tolerance of 8%.
As shown in these two example calculations, the maximum
output frequency for ac inputs is always half of that for dc
input signals. Table III shows a complete listing of all maxi-
mum output frequencies.
S1
0
0
1
1
Frequency Output CF
The pulse output CF (calibration frequency) is intended for use
during calibration. The output pulse rate on CF can be up to 128
times the pulse rate on F1 and F2. The lower the F
selected the higher the CF scaling. Table IV shows how the two
frequencies are related depending on the states of the logic inputs
S0, S1, and SCF. Because of its relatively high-pulse rate, the
frequency at this logic output is proportional to the instantaneous
real power. As is the case with F1 and F2, the frequency is derived
from the output of the low-pass filter after multiplication. However,
because the output frequency is high, this real power information
is accumulated over a much shorter time. Hence, less averaging
is carried out in the digital-to-frequency conversion. With much
less averaging of the real power signal, the CF output is much
more responsive to power fluctuations (see Figure 2).
REV. 0
1–4
1–4
REF
REF
Freq
Freq
= 1, G0 = G1 = 0
= 1.7 Hz, S0 = S1 = 0
= rms of 660 mV peak ac = 0.66/ 2 V
= rms of 660 mV peak ac = 0.66/ 2 V
= 2.5 V (nominal reference value)
S0
0
1
0
1
= 1, G0 = G1 = 0
= 1.7 Hz, S0 = S1 = 0
= +660 mV dc = 0.66 V (rms of dc = dc)
= –660 mV dc = 0.66 V (rms of dc = |dc|)
= 2.5 V (nominal reference value)
5 74 0 66 0 66 1 1 7
5 74
.
.
Max Frequency
for DC Inputs (Hz)
0.68
1.36
2.72
5.44
0 66
.
.
2
2 5
.
Table III.
.
0 66
2
.
2
2 5
.
1 1 7
2
.
.
Hz
Hz
Max Frequency
for AC Inputs (Hz)
0.34
0.68
1.36
2.72
0 68
.
0 34
.
1–4
Hz
frequency
Hz
(9)
(8)
–15–
SCF
1
0
1
0
1
0
1
0
SELECTING A FREQUENCY FOR AN ENERGY METER
APPLICATION
As shown in Table II, the user can select one of four frequencies.
This frequency selection determines the maximum frequency
on F1 and F2. These outputs are intended to be used to drive
the energy register (electromechanical or other). Since only four
different output frequencies can be selected, the available
frequency selection has been optimized for a meter constant of
100 imp/kWhr with a maximum current of between 10 A and
120 A. Table V shows the output frequency for several maximum
currents (I
meter constant is 100 imp/kWhr.
The F
output frequencies on F1 and F2. When designing an energy
meter, the nominal design voltage on Channel 2 (voltage) should
be set to half scale to allow for calibration of the meter constant.
The current channel should also be no more than half scale when the
meter sees maximum load. This will allow overcurrent signals and
signals with high crest factors to be accommodated. Table VI
shows the output frequency on F1 and F2 when both analog
inputs are half scale. The frequencies listed in Table VI align very
well with those listed in Table V for maximum load.
S1
0
0
1
1
1–4
frequencies allow complete coverage of this range of
S1
0
0
0
0
1
1
1
1
S0
0
1
0
1
MAX
) with a line voltage of 220 V. In all cases, the
I
12.5 A
25 A
40 A
60 A
80 A
120 A
MAX
S0
0
0
1
1
0
0
1
1
F
1.7
3.4
6.8
13.6
1–4
F
(Hz)
1.7
1.7
3.4
3.4
6.8
6.8
13.6
13.6
Table V.
Table IV.
Table VI.
1–4
F1 and F2 (Hz)
0.076
0.153
0.244
0.367
0.489
0.733
Frequency on F1 and F2 –
CH1 and CH2
Half-Scale AC Inputs
0.085 Hz
0.17 Hz
0.34 Hz
0.68 Hz
CF Max for AC Signals
(Hz)
128
64
64
32
32
16
16
8
F1, F2 = 21.76
F1, F2 = 21.76
F1, F2 = 43.52
F1, F2 = 21.76
F1, F2 = 43.52
F1, F2 = 21.76
F1, F2 = 43.52
F1, F2 = 43.52
ADE7751