LTC4223CDHD-2#PBF Linear Technology, LTC4223CDHD-2#PBF Datasheet - Page 14
![IC CNTRLR HOT SWAP DUAL 16-DFN](/photos/6/93/69377/16-dfn_05-08-1707_sml.jpg)
LTC4223CDHD-2#PBF
Manufacturer Part Number
LTC4223CDHD-2#PBF
Description
IC CNTRLR HOT SWAP DUAL 16-DFN
Manufacturer
Linear Technology
Type
Hot-Swap Controllerr
Datasheet
1.LTC4223CDHD-2PBF.pdf
(24 pages)
Specifications of LTC4223CDHD-2#PBF
Applications
ATCA, MicroTCA™
Internal Switch(s)
No
Voltage - Supply
2.7 V ~ 6 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
16-WFDFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LTC4223-1/LTC4223-2
There are two different modes of fault time-out for the 3.3V
auxiliary supply: adjustable delay through TIMER capacitor
during power-up when ⎯ A ⎯ U ⎯ X ⎯ P ⎯ G ⎯ O ⎯ O ⎯ D not asserted; fi xed
25μs delay after power-up when ⎯ A ⎯ U ⎯ X ⎯ P ⎯ G ⎯ O ⎯ O ⎯ D asserted
low. Under the situation whereby AUXON toggles low then
high for short duration after power-up while ⎯ A ⎯ U ⎯ X ⎯ P ⎯ G ⎯ O ⎯ O ⎯ D
still pulling low due to output load capacitor, 25μs fault
time-out applies.
When the auxiliary supply is powered up into an output
short, the ACL amplifi er will regulate the gate of the
internal pass transistor to produce 240mA output cur-
rent. At this time a 10μA pull-up current starts charging
up the TIMER pin capacitor until it exceeds its threshold
(1.235V). The internal pass transistor then turns off and
⎯ F ⎯ A ⎯ U ⎯ L ⎯ T pulls low. Thereafter, the TIMER is discharged by
a 2μA pull-down current. The fault fi lter delay is given by
C
After a successful power-up cycle, the ACL amplifi er pro-
tects the auxiliary supply from overcurrent by pulling down
the gate of the internal pass transistor rapidly as shown
in Figure 7. Thereafter, the gate recovers and servos the
output current to about 240mA for 25μs before pulling
down to ground gently, turning the transistor off. At this
time, ⎯ F ⎯ A ⎯ U ⎯ L ⎯ T pulls low and the 12V external MOSFET is
also turned off by the 1mA GATE pull-down current.
14
APPLICATIONS INFORMATION
T
• 123[ms/μF].
200mV/DIV
Figure 6. Short-Circuit Fault on 12V Output
ΔV
12V
12V
5V/DIV
5V/DIV
SENSE
GATE
OUT
5μs/DIV
422312 F06
Whenever the 3.3V auxiliary supply trips off due to an
overcurrent fault, the 12V supply also shuts off. The
auxiliary supply is, however, unaffected by faults on the
12V supply. In either case ⎯ F ⎯ A ⎯ U ⎯ L ⎯ T latches low when the
affected channels turn off, and ⎯ F ⎯ A ⎯ U ⎯ L ⎯ T is cleared by tog-
gling the ON pins. Faults are cleared automatically in the
LTC4223-2 auto-retry version.
If there is signifi cant supply lead inductance, a severe
output short may collapse the input to ground before the
LTC4223 can bring the current under control. In this case
the undervoltage lockout will activate after a 12μs fi lter
delay, and pull the gate down. Then the ACL amplifi er will
take control and regulate the output in active current limit.
Under this situation, the fault time-out is set by TIMER
delay instead of 25μs fi lter delay.
Undervoltage Fault
An undervoltage fault occurs if either AUXIN or 12V
below its undervoltage threshold for longer than 12μs. This
turns off the affected supply’s switch instantly, but does
not clear the fault latches. Further, an undervoltage fault
on one supply does not affect the operation of the other
supply. If the bias supply input, V
threshold for more than 80μs, all supply switches are turned
off and the fault latches are cleared. Operation resumes
from a fresh start-up cycle when V
Figure 7. Short-Circuit Fault on 3.3V
AUXOUT
5V/DIV
1A/DIV
5V/DIV
FAULT
I
LOAD
5μs/DIV
CC
CC
falls below its UVLO
is restored.
AUX
422312 F07
Output
IN
422312f
falls