ISL6140CBZ Intersil, ISL6140CBZ Datasheet - Page 10
![IC CONTROLLER HOT PLUG 8SOIC](/photos/7/36/73614/isl6140cbz_sml.jpg)
ISL6140CBZ
Manufacturer Part Number
ISL6140CBZ
Description
IC CONTROLLER HOT PLUG 8SOIC
Manufacturer
Intersil
Type
Hot-Swap Controllerr
Datasheet
1.ISL6140CBZ.pdf
(19 pages)
Specifications of ISL6140CBZ
Applications
General Purpose, VoIP
Internal Switch(s)
No
Voltage - Supply
36 V ~ 72 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (0.154", 3.90mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL6140CBZ
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ISL6140CBZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
the requirement, and are also readily available
standard values.
The three resistors (R
approach for most cases. But if acceptable values can’t
be found, then consider 2 separate resistor dividers
(one for each pin; both from V
allows the user to adjust or trim either trip point
independently.
Note that the top of the resistor dividers is shown in
Figure 29 as GND (Short pin). In a system where cards
are plugged into a backplane (or any other case where
pins are plugged into an edge connector) the user may
want to take advantage of the order in which pins
make contact. Typically, pins on either end of the card
make contact first (although you may not know which
end is first). If you combine that with designating a pin
near the center as the short pin GND, and make it
shorter than the rest, then it should be the last pin to
make contact.
The advantage of doing this: the V
connections are made first. The IC is powered up, but
since the top of the resistor divider is still open, both
the UV and OV pins are pulled low to V
keep the gate off. This allows the IC time to get
initialized, and also allows the power supply to charge
up any input capacitance. By the time the resistor
divider makes contact, the power supply voltage on the
card is presumably stabilized, and the IC ready to
respond; when the UV pin reaches the proper voltage,
the IC will turn on the GATE of the FET, and starts the
controlled inrush current charging.
Note that this is not a requirement; if the IC gets
powered at the same time as the rest of the board, it
should be able to properly control the inrush current.
But if finer control is needed, there are many variables
involved to consider: the number of pins in the
connector; the lengths of the pins; the amount of
mechanical play in the pin-to-connector interface; the
amount of extra time versus the shorter pin length; the
amount of input capacitance versus the ability of the
power supply to charge it; the manufacturing cost
adder (if any) of different length pins; etc.
Applications: PWRGD/PWRGD
The PWRGD/PWRGD outputs are typically used to
directly enable a power module, such as a DC/DC
converter. The PWRGD (ISL6140) is used for modules
with active low enable (L version); PWRGD (ISL6150)
for those with active high enable (H version). The
modules usually have a pull-up device built-in, as well
as an internal clamp. If not, an external pull-up resistor
may be needed, since the output is open drain. If the
pin is not used, it can be left open.
For both versions, the PG comparator compares the
DRAIN pin to V
if the voltage drop exceeds VPG (1.7V nominal), that
implies the drop across the FET is too high, and the
PWRGD pin should go in-active (power-NO-GOOD).
EE
(connected to the source of the FET);
4
, R
5
10
, R
6
DD
) is the recommended
to V
DD
EE
and V
EE
). This also
, which will
EE
ISL6140, ISL6150
pin
ISL6140 (L version; Figure 6): Under normal
conditions (DRAIN < VPG), the Q2 DMOS will turn on,
pulling PWRGD low, enabling the module.
When the DRAIN is too high, the Q
(high impedance), and the pin will be pulled high by
the external module (or an optional pull-up resistor or
equivalent), disabling the module. If a pull-up resistor
is used, it can be connected to any supply voltage that
doesn’t exceed the IC pin maximum ratings on the
high end, but is high enough to give acceptable logic
levels to whatever signal it is driving. An external
clamp may be used to limit the range.
The PWRGD can also drive an opto-coupler (such as a
4N25), as shown in Figure 7 or LED (Figure 8). In both
cases, they are on (active) when power is good.
Resistors R
voltage, and the amount of current needed by the
loads.
(1.7V)
VPG (1.7V)
(SECTION OF) ISL6140
(L VERSION)
(SECTION OF) ISL6140
(L VERSION)
(1.7V)
VPG
FIGURE 7. ACTIVE LOW ENABLE OPTO-ISOLATOR
VPG
(SECTION OF) ISL6140
(L VERSION)
+
-
+
-
+
-
FIGURE 8. ACTIVE LOW ENABLE WITH LED
FIGURE 6. ACTIVE LOW ENABLE MODULE
+
-
+
+
-
-
12
V
DD
V
V
or R
DD
DD
Q
V
13
2
Q
EE
Q
V
2
V
2
are chosen, based on the supply
EE
EE
PWRGD
DRAIN
PWRGD
DRAIN
PWRGD
DRAIN
C
2
L
+
DMOS will shut off
R
OPTO
12
V
ON/OFF
V
MODULE
IN
ACTIVE
ENABLE
IN
LED (GREEN)
LOW
R
+
-
13
V
V
OUT
OUT
PWRGD
FN9039.4
+
-