LTC4252A-1CMS#TRPBF Linear Technology, LTC4252A-1CMS#TRPBF Datasheet - Page 18
![IC CNTRLR HOTSWAP NEGVOLT 10MSOP](/photos/1/36/13608/10-msop_05-08-1661_sml.jpg)
LTC4252A-1CMS#TRPBF
Manufacturer Part Number
LTC4252A-1CMS#TRPBF
Description
IC CNTRLR HOTSWAP NEGVOLT 10MSOP
Manufacturer
Linear Technology
Type
Hot-Swap Controllerr
Specifications of LTC4252A-1CMS#TRPBF
Applications
General Purpose
Internal Switch(s)
No
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
10-TFSOP, 10-MSOP (0.118", 3.00mm Width)
Family Name
LTC4252A-1
Package Type
MSOP
Operating Temperature (min)
0C
Operating Temperature (max)
70C
Operating Temperature Classification
Commercial
Product Depth (mm)
3mm
Product Height (mm)
0.86mm
Product Length (mm)
3mm
Mounting
Surface Mount
Pin Count
10
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIO S I FOR ATIO
LTC4252-1/LTC4252-2
LTC4252A-1/LTC4252A-2
and eliminates current spikes at insertion. A large external
gate-source capacitor is thus unnecessary for the purpose
of compensating C
capacitor C
for the analog current limit loop.
GATE has two comparators: the GATE low comparator
looks for < 0.5V threshold prior to initial timing or a GATE
start-up cycle; the GATE high comparator looks for < 2.8V
relative to V
tor, sets PWRGD status during GATE startup.
SENSE
The SENSE pin is monitored by the circuit breaker (CB)
comparator, the analog current limit (ACL) amplifier and
the fast current limit (FCL) comparator. Each of these three
measures the potential of SENSE relative to V
SENSE exceeds 50mV, the CB comparator activates the
230µA TIMER pull-up. At 100mV (60mV for the LTC4252A),
the ACL amplifier servos the MOSFET current and, at
200mV, the FCL comparator abruptly pulls GATE low in an
attempt to bring the MOSFET current under control. If any
of these conditions persists long enough for TIMER to
charge C
down and pulls GATE low.
If the SENSE pin encounters a voltage greater than V
the ACL amplifier will servo GATE downwards in an
attempt to control the MOSFET current. Since GATE over-
drives the MOSFET in normal operation, the ACL amplifier
needs time to discharge GATE to the threshold of the
MOSFET. For a mild overload the ACL amplifier can control
the MOSFET current, but in the event of a severe overload
the current may overshoot. At SENSE = 200mV the FCL
comparator takes over, quickly discharging the GATE pin
to near V
amplifier takes over. All the while TIMER is running. The
effect of FCL is to add a nonlinear response to the control
loop in favor of reducing MOSFET current.
Owing to inductive effects in the system, FCL typically
overcorrects the current limit loop and GATE under-
shoots. A zero in the loop (resistor R
gate capacitor) helps the ACL amplifier to recover.
18
T
EE
C
to 4V (see Equation 3), the LTC4252 shuts
IN
is adequate. C
potential. FCL then releases and the ACL
and, together with the DRAIN low compara-
GD
U
. Instead, a smaller value (≥ 10nF)
U
C
also provides compensation
W
C
in series with the
U
EE
. When
ACL
,
SHORT-CIRCUIT OPERATION
Circuit behavior arising from a load side low impedance
short is shown in Figure 6 for the LTC4252. Initially, the
current overshoots the fast current limit level of V
200mV (Trace 2) as the GATE pin works to bring V
control (Trace 3). The overshoot glitches the backplane in
the negative direction and when the current is reduced to
100mV/R
positive direction.
TIMER commences charging C
current limit loop maintains the fault current at 100mV/R
which in this case is 5A (Trace 2). Note that the backplane
voltage (Trace 1) sags under load. Timer pull-up is accel-
erated by V
PWRGD pulls high, the load current drops to zero and the
backplane rings up to over 100V. The transient associated
with the GATE turn off can be controlled with a snubber to
reduce ringing and a transient voltage suppressor (such
as Diodes Inc. SMAT70A) to clip off large spikes. The choice
of RC for the snubber is usually done experimentally. The
value of the snubber capacitor is usually chosen between
10 to 100 times the MOSFET C
ber resistor is typically between 3Ω to 100Ω.
200mV/DIV
–48RTN
50V/DIV
10V/DIV
SENSE
5V/DIV
TIMER
GATE
Figure 6. Output Short-Circuit Behavior of LTC4252
S
, the backplane responds by glitching in the
OUT
SUPPLY RING OWING TO
CURRENT OVERSHOOT
. When C
ANALOG CURRENT LIMIT
ONSET OF OUTPUT SHORT-CIRCUIT
FAST CURRENT LIMIT
T
0.5ms/DIV
reaches 4V, GATE turns off,
C
TIMER
OSS
T
SUPPLY RING OWING TO
MOSFET TURN OFF
(Trace 4) while the analog
RAMP
. The value of the snub-
LATCH OFF
4252-1/2 F06
GS
SENSE
under
425212fb
S
=
,