ISL6140IB Intersil, ISL6140IB Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL6140IB
Manufacturer Part Number
ISL6140IB
Description
IC CTRLR HOT PLUG NEG VOLT 8SOIC
Manufacturer
Intersil
Type
Hot-Swap Controllerr
Datasheet
1.ISL6140CBZ.pdf
(19 pages)
Specifications of ISL6140IB
Applications
General Purpose, VoIP
Internal Switch(s)
No
Voltage - Supply
36 V ~ 72 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (0.154", 3.90mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL6140IB
Manufacturer:
HARRIS
Quantity:
5 536
Part Number:
ISL6140IBZ
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL6140IBZ-T
Manufacturer:
Intersil
Quantity:
4
Company:
Part Number:
ISL6140IBZ-T
Manufacturer:
Intersil
Quantity:
14 000
The Enable input often has a pull-up resistor or current
source, or equivalent built in; care must be taken in
the ISL6150 (H version) output that the given current
will create a high enough input voltage (remember that
current through the RPG 6.2kΩ resistor generates the
high voltage level; (see Figure 9).
The input capacitance of the brick is chosen to match
its system requirements, such as filtering noise, and
maintaining regulation under varying loads. Note that
this input capacitance appears as the load capacitance
of the ISL6140/ISL6150.
The brick’s output capacitance is also determined by
the system, including load regulation considerations.
However, it can affect the ISL6140 and ISL6150,
depending upon how it is enabled. For example, if the
PWRGD signal is not used to enable the brick, the
following could occur. Sometime during the inrush
current time, as the main power supply starts charging
the brick input capacitors, the brick itself will start
working, and start charging its output capacitors and
load; that current has to be added to the inrush
current. In some cases, the sum could exceed the
overcurrent shutdown, which would shut down the
whole system! Therefore, whenever practical, it is
advantageous to use the PWRGD output to keep the
brick off at least until the input caps are charged up,
and then start-up the brick to charge its output caps.
Typical brick regulators include models such as Lucent
JW050A1-E or Vicor VI-J30-CY. These are nominal -48V
input, and 5V outputs, with some isolation between the
input and output.
12
ISL6140, ISL6150
Applications: Layout
Considerations
For the minimum application, there are only 6
resistors, 2 capacitors, one IC and one FET. A sample
layout is shown in Figure 30. It assumes the IC is
8-SOIC; the FET is in a D2PAK (or similar SMD-220
package).
Although GND planes are common with multi-level
PCBs, for a -48V system, the -48V rails (both input and
output) act more like a GND than the top 0V rail
(mainly because the IC signals are mostly referenced
to the lower rail). So if separate planes for each voltage
are not an option, consider prioritizing the bottom rails
first.
Note that with the placement shown, most of the signal
lines are short, and there should not be much
interaction between them.
Although decoupling capacitors across the IC supply
pins are often recommended in general, this
application may not need one, nor even tolerate one.
For one thing, a decoupling cap would add to (or be
swamped out by) any other input capacitance; it also
needs to be charged up when power is applied. But
more importantly, there are no high speed (or any)
input signals to the IC that need to be conditioned. If
still desired, consider the isolation resistor R
shown in Figure 29.
10
, as
FN9039.4