MC3PHACVPE Freescale Semiconductor, MC3PHACVPE Datasheet - Page 27

• Manufacturer Part Number: MC3PHACVPE
• Description: IC MOTOR CONTROLLER 28-DIP
• Manufacturer: Freescale Semiconductor

Specifications of MC3PHACVPE

• Applications: AC Motor Controller, 3 Phase
• Number Of Outputs: 1
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Through Hole
• Package / Case: 28-DIP (0.600", 15.24mm)
• Processor Series: MC3PHAC
• Core: HC08
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 256 KB
• Interface Type: RS-232
• Maximum Clock Frequency: 21.16 KHz
• Number Of Programmable I/os: 14
• Number Of Timers: 1
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• Controller Family/series: HC08
• Core Size: 8 Bit
• Ram Memory Size: 256Byte
• Embedded Interface Type: SCI
• Digital Ic Case Style: DIP
• No. Of Pins: 28
• A/d Converter: 10 Bits
• No. Of Timers 8/12/16/32 Bits: 0/0/2/0
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output: -
• Voltage - Load: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Freescale Semiconductor
FUNCTIONAL
Address: $FE01
Reset
PC MASTER
FAULT BITS
SOFTWARE
POWER UP
RESET PIN
COMMAND
MC3PHAC
VOLTAGE
LOW V
RESET
W
R
Field
5–4
7
6
1
POWER
DD
UP
1
7
POWER UP Bit — This read-only bit indicates the last system reset was caused by the power-up
reset detection circuit.
0 Power-up reset was not the source of the reset or a read of the reset status register after the
1 The last reset was caused by an initial power-up of the MC3PHAC.
RESET PIN Bit — This read-only bit indicates the last system reset was caused from the RESET
input pin.
0 The RESET pin was not the source of the reset or a read of the reset status register after the
1 Last reset was caused by an external reset applied to the RESET input pin.
MC3PHAC FUNCTIONAL FAULT Bits — This read-only bit indicates if the last system reset was
the result of an internal system error.
0 The FUNCTIONAL FAULT was not the source of the reset or a read of the reset status register
1 MC3PHAC internal system error
PC MASTER SOFTWARE RESET COMMAND Bit — This read-only bit indicates the last system
reset was the result of a PC master software reset command.
0 The PC master software RESET COMMAND was not the source of the reset or a read of the
1 The MC3PHAC was reset by the PC master software command reset as the result of a write
LOW V
applied to the MC3PHAC.
0 The LOW V
1 The last reset was caused by the low power supply detection circuit.
first read.
first read.
after the first read.
reset status register after the first read.
of $30 to location $1000
first read.
= Unimplemented or Reserved
RESET
DD
PIN
0
6
Table 10. Reset Status Register Field Descriptions
VOLTAGE Bit — This read-only bit indicates if the last reset was the result of low V
MC3PHAC Monolithic Intelligent Motor Controller, Rev. 2
DD
FUNCTIONAL
was not the source of the reset or a read of the reset status register after the
MC3PHAC
FAULT
Figure 17. Reset Status Register
5
0
FUNCTIONAL
MC3PHAC
FAULT
4
0
Description
PC MASTER
SOFTWARE
COMMAND
RESET
0
3
0
2
VOLTAGE
LOW V
1
0
DD
Operation
0
0
DD
27