NCP1605ADR2G ON Semiconductor, NCP1605ADR2G Datasheet - Page 28

• Manufacturer Part Number: NCP1605ADR2G
• Description: IC PFC CONTROLLER CCM/DCM 16SOIC
• Manufacturer: ON Semiconductor

Specifications of NCP1605ADR2G

• Mode: Continuous Conduction (CCM), Discontinuous Conduction (DCM)
• Frequency - Switching: 250kHz
• Current - Startup: 12mA
• Voltage - Supply: 10 V ~ 20 V
• Operating Temperature: 0°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (3.9mm Width)
• Switching Frequency: 250 KHz
• Maximum Power Dissipation: 550 mW
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

More specifically, when the circuit is in OFF state:
•
•
•
•
V
⇒ the circuit enters the
working phase
V
⇒ the circuit enters the
latched−off phase
V
⇒ the circuit enters the
startup phase
V
⇒ the circuit resets
The figures on the following pages portray the circuit behavior during a startup phase:
The drive output is kept low
All the blocks are off except:
In case of normal conditions (Figure 70).
As a function of the brown−out pin voltage (Figure 71).
CC
CC
CC
CC
1. The UVLO circuitry that keeps monitoring the
2. The TSD (thermal shutdown)
3. The “STDWN” latch that stores its output state.
4. The Undervoltage Protection (“UVP”).
5. The brown−out circuitry. One must note that the
6. The high voltage, startup current source when the
goes below V
exceeds V
drops below V
goes below V
V
V
source accordingly.
comparator is reset during the latched−off phase
so that its threshold is the upper one (1 V) when
the circuit enters the active phase (refer to next
“V
circuit is in startup phase (that is when V
lower than V
CC
CC
CC
Conditions
voltage and controlling the startup current
sequences” section).
CC
CC
ON
CC
CC
RESET
STUP
CC
OFF
STUP).
The startup current source is disabled
The circuit is fully active
The circuit is in OFF state
The brown−out block resets during the
latched−off phase so that its comparator
threshold is forced to be the upper one (1 V)
The high voltage, startup current source turns
on to charge V
The drive output and the “pfcOK” are in low
state (the circuit is off)
All the circuit blocks are reset except:
The high voltage, startup current source is on.
The whole circuitry is reset including the
“TSD” and the “STDWN” latch. After reset,
the TSD threshold is 150°C and the output of
the “STDWN latch” is low.
(no condition forces the circuit off)
The thermal shutdown (TSD) and the
brown−out block that keep operating
The “STDWN” latch.
CC
“OFF” is Low
.
CC
http://onsemi.com
is
28
•
•
•
V
in accordance to the V
CC
The following table summarizes the state of the circuit
The Pin 3 capacitor is discharged and kept grounded
along the OFF time, to initialize it for the next
operating sequence, where it must be slowly and
gradually charged to offer some soft−start.
The “pfcOK” pin is grounded.
The output of the “V
grounded
Sequences
The startup current source is disabled
The circuit is in OFF state
The circuit is in OFF state
The brown−out block resets during the latched−off
phase so that its comparator threshold is forced to be
the upper one (1 V)
The high voltage, startup current source turns on to
charge V
The drive output and the “pfcOK” are in low state (the
circuit is off)
All the circuit blocks are reset except:
The high voltage, startup current source is on.
The whole circuitry is reset including the “TSD” and the
“STDWN” latch. After reset, the TSD threshold is 150°C
and the output of the “STDWN latch” is low.
(due to some protection like the thermal shutdown)
The thermal shutdown (TSD) and the brown−out
block that keep operating
The “STDWN” latch.
CC
.
CC
TON
“OFF” is High
level.
processing block” is