ISL6443IRZ-T Intersil, ISL6443IRZ-T Datasheet - Page 17
![IC CTRLR PWM DUAL 300KHZ 28-QFN](/photos/7/54/75412/isl6540acrz-t_sml.jpg)
ISL6443IRZ-T
Manufacturer Part Number
ISL6443IRZ-T
Description
IC CTRLR PWM DUAL 300KHZ 28-QFN
Manufacturer
Intersil
Datasheet
1.ISL6443IRZ.pdf
(18 pages)
Specifications of ISL6443IRZ-T
Applications
Power Supplies
Current - Supply
50µA
Voltage - Supply
5.6 V ~ 24 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
28-QFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL6443IRZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ISL6443IRZ-TK
Manufacturer:
INTERSIL
Quantity:
20 000
Input Capacitor Selection
The important parameters for the bulk input capacitor(s) are
the voltage rating and the RMS current rating. For reliable
operation, select bulk input capacitors with voltage and
current ratings above the maximum input voltage and largest
RMS current required by the circuit. The capacitor voltage
rating should be at least 1.25 times greater than the
maximum input voltage and 1.5 times is a conservative
guideline. The AC RMS Input current varies with the load.
The total RMS current supplied by the input capacitance is:
where,
DC is duty cycle of the respective PWM.
Depending on the specifics of the input power and its
impedance, most (or all) of this current is supplied by the
input capacitor(s). Figure 20 shows the advantage of having
the PWM converters operating out of phase. If the
converters were operating in phase, the combined RMS
current would be the algebraic sum, which is a much larger
value as shown. The combined out-of-phase current is the
square root of the sum of the square of the individual
reflected currents and is significantly less than the combined
in-phase current.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
I
I
RMS
RMSx
=
=
I
2
RMS1
DC DC
–
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
+
I
2
RMS2
2
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
⋅
I
O
For information regarding Intersil Corporation and its products, see www.intersil.com
17
ISL6443
Use a mix of input bypass capacitors to control the voltage
ripple across the MOSFETs. Use ceramic capacitors for the
high frequency decoupling and bulk capacitors to supply the
RMS current. Small ceramic capacitors can be placed very
close to the upper MOSFET to suppress the voltage induced
in the parasitic circuit impedances.
For board designs that allow through-hole components, the
Sanyo OS-CON® series offer low ESR and good
temperature performance. For surface mount designs, solid
tantalum capacitors can be used, but caution must be
exercised with regard to the capacitor surge current rating.
These capacitors must be capable of handling the surge-
current at power-up. The TPS series available from AVX is
surge current tested.
4.5
3.5
2.5
1.5
0.5
5
4
3
2
1
0
0
FIGURE 20. INPUT RMS CURRENT vs LOAD
OUT OF PHASE
1
3.3V AND 5V LOAD CURRENT
IN PHASE
2
3
3.3V
4
August 9, 2006
FN9044.2
5V
5