ISL6125IR Intersil, ISL6125IR Datasheet - Page 8
![IC SEQUENCER POWER 4-CH 24-QFN](/photos/6/89/68941/20-24-qfn_sml.jpg)
ISL6125IR
Manufacturer Part Number
ISL6125IR
Description
IC SEQUENCER POWER 4-CH 24-QFN
Manufacturer
Intersil
Datasheet
1.ISL6123IRZA.pdf
(22 pages)
Specifications of ISL6125IR
Applications
Power Supply Sequencer
Voltage - Supply
1.5 V ~ 5.5 V
Current - Supply
200µA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
24-VQFN
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Voltage - Input
-
asserted and pulled low. Next, all four shutdown ramp
capacitors on the DLY_OFF pins are charged with a 1µA
source and when any ramp-capacitor reaches DLY_Vth, a
latch is set and a current is sunk on the respective GATE
pin to turn off its external MOSFET. When the GATE
voltage is approximately 0.6V, the GATE is pulled down the
rest of the way at a higher current level. Each individual
external FET is thus turned off removing the voltages from
the load in the programmed sequence.
The ISL6123 and ISL6124 have the same functionality
except for the ENABLE active polarity with the ISL6124
having an ENABLE input. Additionally, the ISL6123 and
ISL6130 also have an ultra low power sleep state when
ENABLE is low.
The ISL6125 has the same personality as the ISL6124 but
instead of charged pump driven GATE outputs it has open
drain outputs that can be pulled up to a maximum of VDD.
The ISL6126 and ISL6130 are different in that their
sequence on is not time determined but voltage
determined. Each of the four channels operates
independently so that once the IC is biased and any one of
the UVLO inputs is greater than the 0.63V internal
reference, the enable input is also satisfied and the GATE
for the associated UVLO input will turn-on. In turn, the other
UVLO inputs need to be satisfied for the associated GATEs
to turn-on. 150ms after all GATEs are fully on (GATE
voltage = VQP), the RESET is released to go high. The
UVLO inputs can be driven by either a previously turned on
output rail offering a voltage determined sequence or by
logic signal inputs. Any subsequent UVLO level < its
programmed level will pull the associated GATE and
RESET output low (if previously released), but will not
latch-off the other GATEs. Predetermined turn-off is
accomplished by deasserting enable, this will cause
RESET to latch low and all four GATE outputs to follow the
programmed turn off sequence similar to ISL6124.
The ISL6127 is a four-channel sequencer pre-programmed
for A-B-C-D turn-on and D-C-B-A turn-off. After all four
UVLO and ENABLE inputs are satisfied for ~10ms, the
sequencing starts and the next GATE in the sequence
starts to ramp-up once the previous GATE has reached
~VQP-1V. 160ms after the last GATE is at VQP, the RESET
output will be deasserted. Once any UVLO is unsatisfied,
RESET is pulled low, SYSRST is pulled low and all GATEs
are simultaneously turned off. When ENABLE is signaled
high the D GATE will start to pull low and once below 0.6V
the next GATE will then start to pull low and so on until all
GATEs are at 0V. Unloaded, this turn off sequence will
complete in <1ms. This variant offers a lower cost and size
implementation as the external delay capacitors are not
used. Since the delay capacitors are not used, this IC
cannot delay the start of subsequent GATEs, thus
necessary stabilization or system house keeping need to
be considered.
ISL6123, ISL6124, ISL6125, ISL6126, ISL6127, ISL6128, ISL6130
8
The ISL6128 is a four-channel device that groups the four
channels into two groups of two channels each, as A, B
and C, D, each group having its own ENABLE and RESET
I/IO pins. This requires all four UVLO and both ENABLEs to
be satisfied for sequencing to start. The A, B group will first
turn on 10ms after the second ENABLE is pulled low with A
then B turning on followed by C then D. Once the preceding
GATE = VQP the next DLY_ON pin starts to charge its
capacitor thus turning on all four GATEs. Approximately
160ms after D GATE = VQP the RESET output is released to
go high. Once any UVLO is unsatisfied, only the related
group’s RESET and two GATEs are pulled low. The related
EN input has to be cycled for the faulted group to be turned-on
again. Normal shutdown is invoked by either signaling both
ENABLE inputs high which will cause all the two related
GATEs to shutdown in reverse order from turn-on. DLY_X
capacitors adjust the delay between GATES during turn on
and off but not the order.
During bias up the RESET output is guaranteed to be in the
correct state with VDD lower than 1V.
The SYSRST pin follows the VDD upon power-up with a weak
internal pull-up and is both an input and output connection
providing two functions. As an input, if it is pulled low, all
GATEs will be unconditionally shut off and RESET pulls low,
(see Figure 7). This input can also be used as a no wait
enabling input, if all inputs (ENABLE and UVLO) are satisfied,
it does not wait through the ~10ms enable delay to initiate
DLY_ON capacitor charging when released to go high. As an
output, it is useful when implementing multiple sequencers in
a design needing simultaneous shutdown as with a kill switch
across all sequencers. Once any UVLO is unsatisfied longer
than tFIL the related SYSRST will pull low and pull all other
SYSRST inputs low that are on a common connection thus
unconditionally shutting down all outputs across multiple
sequencers.
Except for the ISL6128 after a fault, restart of the turn-on
sequence is automatic once all requirements are met. This
allows for no interaction between the sequencer and a
controller IC if desired. The ENABLE and RESET I/O do allow
for a higher level of feedback and control if desired. The
ISL6128 requires that the related ENABLE be cycled for
restart of its associated group GATEs. If no capacitors are
connected between DLY_ON or DLY_OFF pins and ground
then all such related GATEs start to turn on immediately after
the 10ms (TUVLOdel) ENABLE stabilization time out has
expired and the GATEs start to immediately turn off when
ENABLE is asserted.
If some of the rails are to be sequenced together in order to
eliminate the effect of capacitor variance on the timing and to
reduce cost, a common capacitor can be connected to two or
more DLY_ON or DLY_OFF pins. In this case multiply the
capacitor value by the number of common DLY_X pins to
retain the desired timing.
Table 1 illustrates the nominal time delay from the start of
October 15, 2008
FN9005.10