HIP6501ACB-T Intersil, HIP6501ACB-T Datasheet
HIP6501ACB-T
Specifications of HIP6501ACB-T
Available stocks
Related parts for HIP6501ACB-T
HIP6501ACB-T Summary of contents
Page 1
... Ordering Information output is DUAL PART NUMBER HIP6501ACB HIP6501ACBZ (Note) HIP6501AEVAL1 *Add “-T” suffix to part number for tape and reel packaging. NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations ...
Page 2
Block Diagram 12V 3V3DLSB 12V BIAS 12V MONITOR 10.8V/9.0V FAULT/MSEL UV DETECTOR + - MEM VOLTAGE + 40µA SELECT COMP 0. COMPARATOR - 5VDL + + 3.75V 10µA - 3V3DL 5VSB EA4 - + 5VSB POR 4.5V/4.0V MONITOR ...
Page 3
Simplified Power System Diagram +5V IN +12V IN +5V SB +3. 3.3V DUAL FAULT SHUTDOWN S3 S5 EN5VDL EN3VDL Typical Application +5V IN +12V IN +5V SB +3. OUT1 3.3V DUAL FAULT SLP_S3 SLP_S5 ...
Page 4
Absolute Maximum Ratings Supply Voltage +7.0V 5VSB 12V. . ...
Page 5
Electrical Specifications Recommended Operating Conditions, Unless Otherwise Noted. Refer to Figures 1, 2 and 3 (Continued) PARAMETER 5VDUAL SWITCH CONTROLLER (V OUT3 5VDL Under-Voltage Rising Threshold 5VDL Under-Voltage Hysteresis 5VDLSB Output Drive Current 5VDLSB Pull-up Impedance to 5VSB TIMING INTERVALS ...
Page 6
FAULT pin low. The C capacitor is also used to SS provide a controlled voltage slew rate during active-to-sleep transitions on the 3.3V and 2.5/3.3V DUAL 12V (Pin 14) Connect this pin to the ATX (or equivalent) 12V ...
Page 7
TABLE 2. 5V OUTPUT (V DUAL OUT3 EN5VDL S5 S3 5VDL S0, S1 STATES (Active Note 5 Maintains Previous State S4/ ...
Page 8
S3 S5 12V 3V3DLSB DLA 3V3DL 5VDLSB 5VDL FIGURE 6. 3V AND 5V TIMING DIAGRAM FOR DUAL DUAL EN3VDL = 0, EN5VDL = 1 5VSB S3 S5 12V 3V3DLSB DLA 3V3DL 5VDLSB 5VDL FIGURE 7. 3V AND 5V TIMING ...
Page 9
Soft-Start into Active States (S0, S1) If both S3 and S5 are logic high at the time the 5VSB is applied, the HIP6501A will assume an active state and keep off the controlled external transistors until about 50ms after the ...
Page 10
FAULT/MSEL MEM VOLTAGE R SEL SELECT COMP 40µ SEL MEM 1kΩ 2.5V 10kΩ 3.3V FIGURE 11. 2.5/3.3V OUTPUT VOLTAGE SELECTION MEM CIRCUITRY DETAILS Application Guidelines Soft-Start Interval The 5VSB output of a typical ATX supply is capable of ...
Page 11
The only critical small signal component is the soft-start capacitor ...
Page 12
P-Channel MOSFET is used to switch the 5VSB output of the ATX supply into the 5V output during S3 and DUAL S4/S5 states (as dictated by EN5VDL status), then, similar to the situation where ...
Page 13
... HUF76113SK8. Q4 can also be a PNP, such as an MMBT2907AL. For detailed information on the circuit, including a Bill-of-Materials and circuit board description, see DUAL Application Note AN9846. memory voltage ) from +3.3V, +5V, See Intersil’s web site www.intersil.com for the latest information 10µF C4 1µF ...
Page 14
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...