DS1626S+T&R Maxim Integrated Products, DS1626S+T&R Datasheet
DS1626S+T&R
Specifications of DS1626S+T&R
Related parts for DS1626S+T&R
DS1626S+T&R Summary of contents
Page 1
DESCRIPTION The DS1626 and DS1726 thermometers/thermostats provide temperature measurements and stand-alone capability over a -55°C to +125°C range. The DS1626 offers ±0.5°C accuracy from 0°C to +70°C and the DS1726 has ±1°C accuracy from -10°C to +85°C. The resolution ...
Page 2
PIN DESCRIPTION PIN NAME 1 DQ Data Input/Output Pin (Tri-State) for 3-Wire Serial Communication Clock Input Pin for 3-Wire Serial Communication. Controls temperature 2 CLK/CNV measurements when the DS1626/DS1726 is configured as a stand-alone thermostat. RST 3 Reset Input Pin ...
Page 3
ABSOLUTE MAXIMUM RATINGS Voltage Range on Any Pin Relative to Ground...................................................................-0.5V to +6.0V Operating Temperature Range.............................................................................................-55°C to +125°C Storage Temperature Range ................................................................................................-55°C to +125°C Solder Dip Temperature (10s) .............................................................................................+260°C Reflow Oven Temperature ..................................................................................................+220°C These are stress ratings only and functional ...
Page 4
EEPROM AC ELECTRICAL CHARACTERISTICS (V = 2.7V to 5.5V PARAMETER EEPROM Write Cycle Time EEPROM Writes EEPROM Data Retention AC ELECTRICAL CHARACTERISTICS (V = 2.7V to 5.5V PARAMETER Temperature Conversion Time Data In to ...
Page 5
Figure 2. TYPICAL OPERATING CURVES DS1626 0.8 0.6 0.4 0.2 +3σ 0 -0.2 -0.4 -0.6 -3σ -0 REFERENCE TEMPERATURE (°C) Figure 3. TIMING DIAGRAMS a) Read Timing Write Timing t RC 0.8 ...
Page 6
OPERATION—MEASURING TEMPERATURE The DS1626/DS1726 measure temperature using a bandgap-based temperature sensor. A delta-sigma analog-to-digital converter (ADC) converts the measured temperature to a digital value that is calibrated in degrees Celsius; for Fahrenheit applications a lookup table or conversion routine must ...
Page 7
Table 2. 12-BIT RESOLUTION TEMPERATURE/DATA RELATIONSHIP TEMPERATURE (°C) +125 +25.0625 +10.125 +0.5 0 -0.5 -10.125 -25.0625 -55 OPERATION—THERMOSTAT FUNCTION The DS1626/DS1726 thermostat outputs (T conversion and remain at the updated values until the next conversion completes. T the measured temperature ...
Page 8
CPU BIT AND STAND-ALONE THERMOSTAT OPERATION In stand-alone thermostat mode, DS1626/DS1726 thermostat functionality can be used without requiring a microcontroller to start/stop temperature conversions. The CPU bit in the configuration register determines if stand-alone mode is enabled. When CPU = ...
Page 9
CONFIGURATION REGISTER The configuration register allows the user to customize the DS1626/DS1726 conversion and thermostat options. It also provides information to the user about conversion status, EEPROM activity, and thermostat activity. The configuration register is arranged as shown in Figure ...
Page 10
Table 4. RESOLUTION CONFIGURATION RESOLUTION R1 R0 (BITS 3-WIRE SERIAL DATA BUS The 3-wire bus consists of three signals: RST (active-low reset), CLK (clock), and DQ (data). 3-wire ...
Page 11
Figure 7. 3-WIRE COMMUNICATION a) Start Temperature Conversion RST CLK DQ b) Write to the T /T Registers H L RST CLK Write TH [01h [02h] Command c) Write to ...
Page 12
... No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation. 0101 0001 0010 0010 ...