DS18B20-PAR+T&R Maxim Integrated Products, DS18B20-PAR+T&R Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS18B20-PAR+T&R
Manufacturer Part Number
DS18B20-PAR+T&R
Description
IC THERM MICROLAN PROG-RES TO-92
Manufacturer
Maxim Integrated Products
Specifications of DS18B20-PAR+T&R
Function
Thermometer, Thermostat
Topology
Register Bank, Scratchpad
Sensor Type
Internal
Sensing Temperature
-55°C ~ 100°C
Output Type
1-Wire®
Output Alarm
Yes
Output Fan
No
Voltage - Supply
3 V ~ 5.5 V
Operating Temperature
-55°C ~ 100°C
Mounting Type
Through Hole
Package / Case
TO-92-3 (Standard Body), TO-226
Full Temp Accuracy
+/- 2 C
Digital Output - Bus Interface
Serial (1-Wire)
Digital Output - Number Of Bits
12 bit
Maximum Operating Temperature
+ 100 C
Minimum Operating Temperature
- 55 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
PARASITE POWER
The DS18B20-PAR’s parasite power circuit allows the DS18B20-PAR to operate without a local external
power supply. This ability is especially useful for applications that require remote temperature sensing or
that are very space constrained. Figure 1 shows the DS18B20-PAR’s parasite-power control circuitry,
which “steals” power from the 1-Wire bus via the DQ pin when the bus is high. The stolen charge
powers the DS18B20-PAR while the bus is high, and some of the charge is stored on the parasite power
capacitor (C
The 1-Wire bus and C
as long as the specified timing and voltage requirements are met (refer to the DC ELECTRICAL
CHARACTERISTICS and the AC ELECTRICAL CHARACTERISTICS sections of this data sheet).
However, when the DS18B20-PAR is performing temperature conversions or copying data from the
scratchpad memory to EEPROM, the operating current can be as high as 1.5 mA. This current can cause
an unacceptable voltage drop across the weak 1-Wire pullup resistor and is more current than can be
supplied by C
provide a strong pullup on the 1-Wire bus whenever temperature conversions are taking place or data is
being copied from the scratchpad to EEPROM. This can be accomplished by using a MOSFET to pull
the bus directly to the rail as shown in Figure 2. The 1-Wire bus must be switched to the strong pullup
within 10 μs (max) after a Convert T [44h] or Copy Scratchpad [48h] command is issued, and the bus
must be held high by the pullup for the duration of the conversion (t
No other activity can take place on the 1-Wire bus while the pullup is enabled.
SUPPLYING THE DS18B20-PAR DURING TEMPERATURE CONVERSIONS
Figure 2
OPERATION – MEASURING TEMPERATURE
The core functionality of the DS18B20-PAR is its direct-to-digital temperature sensor. The resolution of
the temperature sensor is user-configurable to 9, 10, 11, or 12 bits, which corresponds to increments of
0.5°C, 0.25°C, 0.125°C, and 0.0625°C, respectively. The default resolution at power-up is 12-bit.
The DS18B20-PAR powers-up in a low-power idle state; to initiate a temperature measurement and A-to-
D conversion, the master must issue a Convert T [44h] command. Following the conversion, the
resulting thermal data is stored in the 2-byte temperature register in the scratchpad memory and the
DS18B20-PAR returns to its idle state.
centigrade; for Fahrenheit applications, a lookup table or conversion routine must be used.
temperature data is stored as a 16-bit sign-extended two’s complement number in the temperature register
(see Figure 3). The sign bits (S) indicate if the temperature is positive or negative: for positive numbers S
= 0 and for negative numbers S = 1. If the DS18B20-PAR is configured for 12-bit resolution, all bits in
the temperature register will contain valid data. For 11-bit resolution, bit 0 is undefined. For 10-bit
processor
Micro-
PP
) to provide power when the bus is low.
PP
. To assure that the DS18B20-PAR has sufficient supply current, it is necessary to
PP
can provide sufficient parasite power to the DS18B20-PAR for most operations
V
PU
4.7K
The DS18B20-PAR output data is calibrated in degrees
V
PU
3 of 19
1-Wire Bus
DS18B20-PAR
GND
conv
DQ
) or data transfer (t
To Other
1-Wire Devices
DS18B20-PAR
wr
= 10 ms).
The