DS1620S Maxim Integrated Products, DS1620S Datasheet - Page 5
![IC THERMOMETER/STAT DIG 8-SOIC](/photos/6/58/65843/8-soic_21-0262_sml.jpg)
DS1620S
Manufacturer Part Number
DS1620S
Description
IC THERMOMETER/STAT DIG 8-SOIC
Manufacturer
Maxim Integrated Products
Datasheet
1.DS1620.pdf
(12 pages)
Specifications of DS1620S
Function
Thermometer, Thermostat
Topology
Comparator, Register Bank
Sensor Type
Internal
Sensing Temperature
-55°C ~ 125°C
Output Type
Digital
Output Alarm
Yes
Output Fan
No
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-55°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
Full Temp Accuracy
+/- 2 C
Digital Output - Bus Interface
Serial (3-Wire)
Digital Output - Number Of Bits
9 bit
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 55 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS1620S
Manufacturer:
DALLAS
Quantity:
4 225
Company:
Part Number:
DS1620S
Manufacturer:
DALLAS
Quantity:
140
Part Number:
DS1620S
Manufacturer:
DALLAS
Quantity:
20 000
Company:
Part Number:
DS1620S+
Manufacturer:
Maxim
Quantity:
4 127
Part Number:
DS1620S+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
DS1620S+T
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
DS1620S+T&R
Manufacturer:
MAXIM
Quantity:
414
Part Number:
DS1620S+T&R
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
DS1620S+TR
Manufacturer:
MAXIM/美信
Quantity:
20 000
THERMOSTAT OUTPUT OPERATION Figure 3
OPERATION AND CONTROL
The DS1620 must have temperature settings resident in the TH and TL registers for thermostatic
operation. A configuration/status register also determines the method of operation that the DS1620 will
use in a particular application and indicates the status of the temperature conversion operation. The
configuration register is defined as follows:
CONFIGURATION/STATUS REGISTER
where
DONE = Conversion Done Bit. 1=conversion complete, 0=conversion in progress. The power-up/POR
state is a 1.
THF
to the value of TH. It will remain 1 until reset by writing 0 into this location or by removing power from
the device. This feature provides a method of determining if the DS1620 has ever been subjected to
temperatures above TH while power has been applied. The power-up/POR state is a 0.
TLF
the value of TL. It will remain 1 until reset by writing 0 into this location or by removing power from the
device. This feature provides a method of determining if the DS1620 has ever been subjected to
temperatures below TL while power has been applied. The power-up/POR state is a 0.
NVB
memory is not busy. A copy to E
CPU
low. If CPU is 1, the DS1620 will be used with a CPU communicating to it over the 3–wire port, and the
operation of the CLK/
nonvolatile E
DONE
= Temperature High Flag. This bit will be set to 1 when the temperature is greater than or equal
= Temperature Low Flag. This bit will be set to 1 when the temperature is less than or equal to
= Nonvolatile Memory Busy Flag. 1=write to an E
= CPU Use Bit. If CPU=0, the CLK/
2
THF
memory, capable of at least 50,000 writes. The DS1620 is shipped with CPU=0.
CONV
TLF
T
T
T
pin is as a normal clock in concert with DQ and
HIGH
COM
LOW
2
may take up to 10 ms. The power-up/POR state is a 0.
NVB
TL
1
CONV
5 of 12
pin acts as a conversion start control, when
0
TH
2
memory cell in progress. 0=nonvolatile
CPU
T(°C)
1SHOT
RST
. This bit is stored in
RST
is