LT6650CS5#TRM Linear Technology, LT6650CS5#TRM Datasheet
![IC REF 400MV R-R BUFFER TSOT23-5](/photos/6/57/65785/tsot-23-5_05-08-1635_sml.jpg)
LT6650CS5#TRM
Specifications of LT6650CS5#TRM
LT6650CS5
Available stocks
Related parts for LT6650CS5#TRM
LT6650CS5#TRM Summary of contents
Page 1
... Stability is ensured with any output capacitor of 1µF or higher. The LT6650 is the lowest voltage series reference available in the 5-lead SOT-23 package. , LTC and LT are registered trademarks of Linear Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. 402 ...
Page 2
LT6650 ABSOLUTE AXI U RATI GS (Note 1) Total Supply Voltage (V to GND)........................... 20V IN FB Voltage (Note 2) ....................... 20V to (GND – 0.3V) Output Voltage (OUT) .................... 20V to (GND – 0.3V) Output Short-Circuit ...
Page 3
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifications are at T otherwise noted. SYMBOL PARAMETER T Output Voltage Temperature C Coefficient (Note 10) ∆V Dropout Voltage (Note Short-Circuit Output Current SC I Supply Current Pin Input ...
Page 4
LT6650 W U TYPICAL PERFOR A CE CHARACTERISTICS Output Voltage Temperature Drift 404 TYPICAL PART 403 402 401 V = 1.4V IN 400 399 V = 18V 398 397 396 –60 –40 – ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS Minimum Input-Output Voltage Differential (Sinking 1.425V - TYP (RF = 100k 39.2k) OUT 0.1% V OUT –100 –55°C –200 25°C –300 –400 125°C –500 10 100 1000 OUTPUT ...
Page 6
LT6650 W U TYPICAL PERFOR A CE CHARACTERISTICS Output Impedance vs Frequency 1000 I = 0µA OUT R = 0Ω 10µF L 100 C = 1µ 47µ 100 1k 10k ...
Page 7
CTIO S FB (Pin 1): Resistor Divider Feedback Pin. Connect a resistor divider from OUT to GND and the center tap to FB. This pin sets the output potential. GND (Pin 2): Ground Connection. DNC ...
Page 8
LT6650 U U APPLICATIO S I FOR ATIO operated from a small battery or other relatively high impedance source, a minimum 1µF capacitor is recom- mended. PSRR can be significantly enhanced by adding a low-pass RC filter on the input, ...
Page 9
U U APPLICATIO S I FOR ATIO step between 100µA and 200µA in Figure 7. Load step settling occurs in about 0.5ms or less (to ±0.2%). Output Adjustment If the LT6650 used as a 400mV reference, then ...
Page 10
LT6650 U U APPLICATIO S I FOR ATIO must be within the following range for proper OUT B operation (the optimal value depends greatly on the direc- tion and magnitude of the load current): R > |V ...
Page 11
... MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. IN ...
Page 12
... Max 6.5µA Supply Current 6.5µA, Choice of Polarities Available in SOT-23 www.linear.com ● 1.4V ≤ V ≤ 18V Z 30µA ≤ I ≤ 220µ 0.4V • ANODE 6650 TA02 < 375µV, I < 1000pA B LT/LT 1005 • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2003 6650fa ...