LT6650CS5#TRM Linear Technology, LT6650CS5#TRM Datasheet - Page 10
![IC REF 400MV R-R BUFFER TSOT23-5](/photos/6/57/65785/tsot-23-5_05-08-1635_sml.jpg)
LT6650CS5#TRM
Manufacturer Part Number
LT6650CS5#TRM
Description
IC REF 400MV R-R BUFFER TSOT23-5
Manufacturer
Linear Technology
Datasheet
1.LT6650CS5TR.pdf
(12 pages)
Specifications of LT6650CS5#TRM
Reference Type
Series
Voltage - Output
400mV
Tolerance
±0.75%
Temperature Coefficient
30ppm/°C
Voltage - Input
1.4 ~ 18 V
Number Of Channels
1
Current - Quiescent
11µA
Current - Output
200µA
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
TSOT-23-5, TSOT-5, TSOP-5
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Current - Cathode
-
Other names
LT6650CS5
LT6650CS5
LT6650CS5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIO S I FOR ATIO
LT6650
V
operation (the optimal value depends greatly on the direc-
tion and magnitude of the load current):
Hysteresis
Due to various mechanical stress mechanisms inherent to
integrated-circuit packaging, internal offsets may not pre-
cisely recover from variations that occur over tempera-
ture, and this effect is referred to as hysteresis. Proprietary
manufacturing steps minimize this hysteresis, though
some small residual error can occur. Hysteresis measure-
ments for the LT6650 can be seen in Figures 11 and 12.
Figure 11 presents the worst-case data taken on parts
subjected to thermal cycling between 0°C to 70°C, while
Figure 12 shows data for –40°C to 85°C cycling. Units
were cycled several times over these temperature ranges
and the largest changes are shown. As would be expected,
10
OUT
R
R
B
B
. R
> |V
< |V
B
Figure 11. Worst-Case 0°C to 70°C Hysteresis
must be within the following range for proper
S
S
– V
– V
6
5
4
3
2
1
0
–400
LIGHT COLUMNS 0°C TO 25°C
DARK COLUMNS 70°C TO 25°C
OUT
OUT
|/(200µA + 0.4/R
|/(15µA + 0.4/R
–200
U
DISTRIBUTION (ppm)
0
U
200
G
W
G
)
400
)
6650 F11
600
U
the parts cycled over the higher temperature extremes
exhibit a broader hysteresis distribution. The worst hys-
teresis measurements indicate voltage shifts of less than
1000ppm (0.1%) from their initial value.
Limits of Operation
The LT6650 is a robust bipolar technology part. ESD
clamp diodes are integrated into the design and are
depicted in the Simplified Schematic for reference. Diodes
are included between the GND pin and the IN, OUT, and FB
pins to prevent reverse voltage stress on the device.
Unusual modes of operation that forward-bias any these
diodes should limit current to 10mA to avoid permanent
damage to the device. The LT6650 is fabricated using a
relatively high-voltage process, allowing any pin to inde-
pendently operate at up to 20V with respect to GND. The
part does not include any over voltage protection mecha-
nisms; therefore caution should be exercised to avoid
inadvertent application of higher voltages in circuits in-
volving high potentials.
Figure 12. Worst-Case –40°C to 85°C Hysteresis
–1000
7
6
5
4
3
2
1
0
LIGHT COLUMNS –40°C TO 25°C
DARK COLUMNS 85°C TO 25°C
–750
–500
DISTRIBUTION (ppm)
–250
0
250
500
750
6650 F12
1000
6650fa