LX1672-03CPW Microsemi Analog Mixed Signal Group, LX1672-03CPW Datasheet - Page 15
![IC CTRLR PS TRIPLE OUTPT 28TSSOP](/photos/7/53/75387/lx1672-03cpw_sml.jpg)
LX1672-03CPW
Manufacturer Part Number
LX1672-03CPW
Description
IC CTRLR PS TRIPLE OUTPT 28TSSOP
Manufacturer
Microsemi Analog Mixed Signal Group
Series
LoadSHARE™r
Datasheet
1.LX1672-03CPW.pdf
(20 pages)
Specifications of LX1672-03CPW
Pwm Type
Voltage Mode
Number Of Outputs
3
Frequency - Max
345kHz
Duty Cycle
85%
Voltage - Supply
4.5 V ~ 5.5 V
Buck
Yes
Boost
No
Flyback
No
Inverting
No
Doubler
No
Divider
No
Cuk
No
Isolated
No
Operating Temperature
0°C ~ 70°C
Package / Case
28-TSSOP
Frequency-max
345kHz
For Use With
LX1671 EVA KIT - KIT EVAL FOR SWITCHING REGULATOR
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Copyright © 2000
Rev. 1.0, 2005-08-10
O
requirements of the output voltage ripple in steady-state operation
and the inductor current slew-rate during transient. The peak-to-
peak output voltage ripple is:
and ESR is the Effective Series Resistance of the output
capacitor.
maximum output current. Higher inductance results in lower
output voltage ripple, allowing slightly higher ESR to satisfy the
transient specification. Higher inductance also slows the inductor
current slew rate in response to the load-current step change, ΔI,
resulting in more output-capacitor voltage droop. When using
electrolytic capacitors, the capacitor voltage droop is usually
negligible, due to the large capacitance
UTPUT
The output inductor should be selected to meet the
where
ΔI is the inductor ripple current, L is the output inductor value
ΔI should typically be in the range of 20% to 40% of the
and
The inductance value can be calculated by
The inductor-current rise and fall times are:
TM
I
NDUCTOR
ΔI
L
T
V
RISE
=
RIPPLE
=
T
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
FALL
V
V
=
IN
IN
L
=
×
−
=
−
ΔI
ESR
L
(
V
L
V
V
×
OUT
OUT
IN
×
V
−
ΔI
ΔI
OUT
I
V
×
RIPPLE
×
OUT
f
D
f
D
)
s
s
A P P L I C A T I O N N O T E
Integrated Products Division
®
Microsemi
O
performance specifications. Effective Series Resistance (ESR) is a
critical parameter. When a step load current occurs, the output
voltage will have a step that equals the product of the ESR and the
current step, ΔI. In an advanced microprocessor power supply, the
output capacitor is usually selected for ESR instead of capacitance
or RMS current capability. A capacitor that satisfies the ESR
requirements usually has a larger capacitance and current capability
than strictly needed. The allowed ESR can be found by:
load current step change, and V
excursion in the transient.
are less stable with age than tantalum capacitors. As they age, their
ESR degrades, reducing the system performance and increasing the
risk of failure. It is recommended that multiple parallel capacitors
be used, so that, as ESR increase with age, overall performance
will still meet the processor’s requirements.
components possible; however, this could lead to degraded long-
term reliability, especially in the case of filter capacitors.
Microsemi’s demonstration boards use the CDE Polymer AL-EL
(ESRE) filter capacitors, which are aluminum electrolytic, and
have demonstrated reliability. The OS-CON series from Sanyo
generally provides the very best performance in terms of long term
ESR stability and general reliability, but at a substantial cost
penalty. The CDE Polymer AL-EL (ESRE) filter series provides
excellent ESR performance at a reasonable cost. Beware of off-
brand, very low-cost filter capacitors, which have been shown to
degrade in both ESR and general electrolytic characteristics over
time.
UTPUT
There is frequently strong pressure to use the least expensive
The output capacitor is sized to meet ripple and transient
Where I
Electrolytic capacitors can be used for the output capacitor, but
Multiple Output LoadSHARE™ PWM
C
APACITOR
RIPPLE
P
RODUCTION
is the inductor ripple current, ΔI is the maximum
ESR
×
(
I
RIPPLE
D
EX
ATA
+
ΔI
is the allowed output voltage
)
S
<
HEET
V
EX
LX1672
Page 15