ISL62871HRUZ-T Intersil, ISL62871HRUZ-T Datasheet - Page 9
![IC CTRLR DC/DC PWM 16-TQFN](/photos/28/20/282037/16-utqfn_l16_sml.jpg)
ISL62871HRUZ-T
Manufacturer Part Number
ISL62871HRUZ-T
Description
IC CTRLR DC/DC PWM 16-TQFN
Manufacturer
Intersil
Datasheet
1.ISL62871HRUZ-T.pdf
(25 pages)
Specifications of ISL62871HRUZ-T
Pwm Type
Controller
Number Of Outputs
1
Frequency - Max
330kHz
Duty Cycle
100%
Voltage - Supply
3.3 V ~ 25 V
Buck
Yes
Boost
No
Flyback
No
Inverting
No
Doubler
No
Divider
No
Cuk
No
Isolated
No
Operating Temperature
-10°C ~ 100°C
Package / Case
16-UTQFN (16-µTQFN)
Frequency-max
330kHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL62871HRUZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
Electrical Specifications
NOTE:
ISL62872 Functional Pin Descriptions
LGATE (Pin 1)
Low-side MOSFET gate driver output. Connect to the gate
terminal of the low-side MOSFET of the converter.
PGND (Pin 2)
Return current path for the LGATE MOSFET driver. Connect
to the source of the low-side MOSFET.
GND (Pin 3)
IC ground for bias supply and signal reference.
EN (Pin 4)
Enable input for the IC. Pulling EN above the V
threshold voltage initializes the soft-start sequence.
VID1 (Pin 5)
Logic input for setpoint voltage selector. Use in conjunction
with the VID0 pin to select among four setpoint reference
voltages.
VID0 (Pin 6)
Logic input for setpoint voltage selector. Use in conjunction
with the VID1 pin to select among four setpoint reference
voltages. External reference input when enabled by
connecting the SET0 pin to the VCC pin.
SREF (Pin 7)
Soft-start and voltage slew-rate programming capacitor
input. Setpoint reference voltage programming resistor input.
Connects internally to the inverting input of the V
setpoint amplifier. See Figure 8 page 12 for capacitor and
resistor connections.
SET0 (Pin 8)
Voltage set-point programming resistor input. See Figure 8
on page 12 for resistor connection.
SET1 (Pin 9)
Voltage set-point programming resistor input. See Figure 8
on page 12 for resistor connection.
OVP Rising Threshold Voltage
OVP Falling Threshold Voltage
OTP Rising Threshold Temperature
(Note 2)
OTP Hysteresis (Note 2)
2. Limits established by characterization and are not production tested.
PARAMETER
9
These specifications apply for T
All typical specifications T
+25°C, unless otherwise specified. Temperature limits established by characterization and are not production
tested. (Continued)
SYMBOL
V
V
T
T
OVRTH
OTRTH
OTHYS
OVFTH
ENTHR
SET
V
V
ISL62871, ISL62872
FB
FB
voltage
A
rising
= %V
= %V
= +25°C, VCC = 5V. Parameters with MIN and/or MAX limits are 100% tested at
SREF
SREF
A
= -10°C to +100°C, unless otherwise stated.
TEST CONDITIONS
SET2 (Pin 10)
Voltage set-point programming resistor input. See Figure 8
on page 12 for resistor connection.
PGOOD (Pin 11)
Power-good open-drain indicator output. This pin changes to
high impedance when the converter is able to supply
regulated voltage. The pull-down resistance between the
PGOOD pin and the GND pin identifies which protective fault
has shut down the regulator. See Table 3 on page 16.
FB (Pin 12)
Voltage feedback sense input. Connects internally to the
inverting input of the control-loop error amplifier. The
converter is in regulation when the voltage at the FB pin
equals the voltage on the SREF pin. The control loop
compensation network connects between the FB pin and the
converter output. See Figure 13 on page 17.
VO (Pin 13)
Output voltage sense input for the R
also serves as the reference input for the overcurrent
detection circuit. See Figure 10 on page 14.
OCSET (Pin 14)
Input for the overcurrent detection circuit. The overcurrent
setpoint programming resistor R
pin to the sense node. See Figure 10 on page 14.
NC (Pin 15)
No internal connection. Pin 15 should be connected to the
GND pin.
PHASE (Pin 16)
Return current path for the UGATE high-side MOSFET
driver. V
polarity detector input. Connect to junction of output inductor,
high-side MOSFET, and low-side MOSFET. See Figures 2
and 3 on page 4.
UGATE (Pin 17)
High-side MOSFET gate driver output. Connect to the gate
terminal of the high-side MOSFET of the converter.
IN
sense input for the R
3
MIN
113
100
OCSET
modulator. Inductor current
-
-
3
modulator. The VO pin
TYP
116
102
150
connects from this
25
MAX
120
106
-
-
August 14, 2008
FN6707.0
UNIT
°C
°C
%
%