HIP6018BCB-T Intersil, HIP6018BCB-T Datasheet
HIP6018BCB-T
Specifications of HIP6018BCB-T
Available stocks
Related parts for HIP6018BCB-T
HIP6018BCB-T Summary of contents
Page 1
... Ordering Information PGND OCSET1 PART NUMBER VSEN1 HIP6018BCB* FB1 HIP6018BCBZ* (Note) COMP1 FB3 * Add “-T” suffix for tape and reel. DRIVE3 NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate GND ...
Page 2
Block Diagram - + 2 HIP6018B FIGURE 1. ...
Page 3
Simplified Power System Diagram +5V IN +3. OUT2 V OUT3 Typical Application +12V IN + +3. OUT2 2.5V C OUT2 Q3 V OUT3 1.5V C OUT3 3 HIP6018B LINEAR REGULATOR PWM1 CONTROLLER HIP6018B ...
Page 4
Absolute Maximum Ratings Supply Voltage .+15V CC ...
Page 5
Electrical Specifications Recommended Operating Conditions, Unless Otherwise Noted. Refer to Figures 1, 2 and 3 (Continued) PARAMETER PWM CONTROLLER ERROR AMPLIFIER DC Gain Gain-Bandwidth Product Slew Rate PWM CONTROLLER GATE DRIVER Upper Drive Source Upper Drive Sink Lower Drive Source ...
Page 6
Functional Pin Description VSEN1 (Pin 19) This pin is connected to the PWM converter’s output voltage. The PGOOD and OVP comparator circuits use this signal to report output voltage status and for over voltage protection. OCSET1 (Pin 20) Connect a ...
Page 7
Description Operation The HIP6018B monitors and precisely controls 4 output voltage levels (Refer to Figures 1, 2, and 3 designed for microprocessor computer applications with 3.3V ...
Page 8
LUV OVER CURRENT LATCH S Q OC1 S R 0.15V + COUNTER - POR OV FIGURE 7. FAULT LOGIC - SIMPLIFIED SCHEMATIC and V to slew up over increased time intervals, without OUT3 generating ...
Page 9
OVER-CURRENT TRIP: V > SET (i • r (ON) > I • OCSET OCSET OCSET I OCSET 200μA VCC UGATE DRIVE OC1 + PHASE - OVER- VCC CURRENT1 LGATE PWM GATE CONTROL PGND HIP6018B ...
Page 10
... Careful component selection, tight layout of the critical components, and short, wide circuit traces minimize the magnitude of voltage spikes. Contact Intersil for evaluation board drawings of the component placement and printed circuit board. There are two sets of critical components in a DC-DC converter using a HIP6018B controller ...
Page 11
OSC DRIVER PWM COMP Δ V OSC - DRIVER + E ERROR AMP REFERENCE DETAILED FEEDBACK COMPENSATION COMP - + HIP6018B REFERENCE FIGURE 11. VOLTAGE-MODE BUCK CONVERTER COMPENSATION DESIGN The ...
Page 12
PWM Output Capacitors Modern microprocessors produce transient load rates above 10A/ns. High frequency capacitors initially supply the transient and slow the current load rate seen by the bulk capacitors. The bulk filter capacitor values are generally determined by the ESR ...
Page 13
Use a mix of input bypass capacitors to control the voltage overshoot across the MOSFETs. Use ceramic capacitance for the high frequency decoupling and bulk capacitors to supply the RMS current. Small ceramic capacitors should be placed very close to ...
Page 14
... VID0 VID1 VID2 VID3 VID4 14 HIP6018B +3.3V DC the circuit, including a Bill-of-Materials and circuit board ), the GTL bus description, see Application Note AN9805. Also see Intersil’s OUT1 ) from web page (http://www.intersil.com). OUT2 C15 1μF C16 1μF VCC 1 20 ...
Page 15
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...