ISL6556BCBZ Intersil, ISL6556BCBZ Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL6556BCBZ
Manufacturer Part Number
ISL6556BCBZ
Description
IC CTRLR MULTIPHASE VRM10 28SOIC
Manufacturer
Intersil
Datasheet
1.ISL6556BCBZ-T.pdf
(24 pages)
Specifications of ISL6556BCBZ
Applications
Controller, Intel VR10X
Voltage - Input
3 ~ 12 V
Number Of Outputs
4
Voltage - Output
0.84 ~ 1.6 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
28-SOIC (7.5mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL6556BCBZ
Manufacturer:
INTERSIL
Quantity:
1 051
Part Number:
ISL6556BCBZ
Manufacturer:
INTERSI
Quantity:
20 000
Company:
Part Number:
ISL6556BCBZ-T
Manufacturer:
INTERSIL
Quantity:
1 999
Part Number:
ISL6556BCBZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
Figures 14, 16 and 16 in the section entitled Input Capacitor
Selection can be used to determine the input-capacitor RMS
current based on load current, duty cycle, and the number of
channels. They are provided as aids in determining the
optimal input capacitor solution. Figure 17 shows the single
phase input-capacitor RMS current for comparison.
PWM Operation
The timing of each converter leg is set by the number of
active channels. The default channel setting for the
ISL6556B is four. One switching cycle is defined as the time
between PWM1 pulse termination signals. The pulse
termination signal is the internally generated clock signal
that triggers the falling edge of PWM1. The cycle time of the
pulse termination signal is the inverse of the switching
frequency set by the resistor between the FS pin and
ground. Each cycle begins when the clock signal commands
the channel-1 PWM output to go low. The PWM1 transition
signals the channel-1 MOSFET driver to turn off the
channel-1 upper MOSFET and turn on the channel-1
synchronous MOSFET. In the default channel configuration,
the PWM2 pulse terminates 1/4 of a cycle after PWM1. The
PWM3 output follows another 1/4 of a cycle after PWM2.
PWM4 terminates another 1/4 of a cycle after PWM3.
If PWM3 is connected to VCC, two channel operation is
selected and the PWM2 pulse terminates 1/2 of a cycle later.
Connecting PWM4 to VCC selects three channel operation
and the pulse-termination times are spaced in 1/3 cycle
increments.
Once a PWM signal transitions low, it is held low for a
minimum of 1/3 cycle. This forced off time is required to
ensure an accurate current sample. Current sensing is
described in the next section. After the forced off time
expires, the PWM output is enabled. The PWM output state
is driven by the position of the error amplifier output signal,
V
sawtooth ramp as illustrated in Figure 4. When the modified
V
transitions high. The MOSFET driver detects the change in
state of the PWM signal and turns off the synchronous
MOSFET and turns on the upper MOSFET. The PWM signal
will remain high until the pulse termination signal marks the
beginning of the next cycle by triggering the PWM signal low.
Current Sensing
During the forced off time following a PWM transition low, the
controller senses channel current by sampling the voltage
across the lower MOSFET r
referenced operational amplifier, internal to the ISL6556B, is
connected to the PHASE node through a resistor, R
The voltage across R
across the r
conducting. The resulting current into the ISEN pin is
proportional to the channel current, I
sampled and held after sufficient settling time every
COMP
COMP
, minus the current correction signal relative to the
voltage crosses the sawtooth ramp, the PWM output
DS(ON)
of the lower MOSFET while it is
ISEN
is equivalent to the voltage drop
DS(ON)
11
(see Figure 3). A ground-
L
. The ISEN current is
ISEN
.
ISL6556B
switching cycle. The sampled current, I
current balance, load-line regulation, overcurrent protection,
and module current sharing. From Figure 3, the following
equation for I
where I
If R
sense resistor in series with the lower MOSFET source can
serve as a sense element. The circuitry shown in Figure 3
represents channel n of an N-channel converter. This
circuitry is repeated for each channel in the converter, but
may not be active depending upon the status of the PWM3
and PWM4 pins as described under PWM Operation
section.
Channel-Current Balance
The sampled current, I
gauge both overall load current and the relative channel
current carried in each leg of the converter. The individual
sample currents are summed and divided by the number of
active channels. The resulting average current, I
provides a measure of the total load current demand on the
converter and the appropriate level of channel current. Using
Figures 3 and 4, the average current is defined as
I
I
where N is the number of active channels and I
total load current.
The average current is subtracted from the individual
channel sample currents. The resulting error current, I
filtered to modify V
compared to a sawtooth ramp signal to produce a modified
I
AVG
AVG
n
SAMPLE
ISL6556B INTERNAL CIRCUIT
HOLD
FIGURE 3. INTERNAL AND EXTERNAL CURRENT-SENSING
=
DS(ON)
&
I
I
n
L
=
=
r
----------------------
L
I
----------------------------------------
I
------------ -
DS ON
R
1
OUT
I
is the channel current.
SEN
N
ISEN
+
(
sensing is not desired, an independent current-
I
2
n
r
----------------------
CIRCUITRY
+
=
N
DS ON
R
)
is derived
…
ISEN
I L
(
+
r
------------------------- -
+
COMP
DS ON
-
R
I
N
ISEN
)
(
n
, from each active channel is used to
. The modified V
)
ISEN(n)
EXTERNAL CIRCUIT
CHANNEL N
LOWER MOSFET
R
ISEN
n
, is used for channel-
COMP
V
IN
+
CHANNEL N
UPPER MOSFET
-
I L r DS ON
December 28, 2004
OUT
signal is
AVG
I
L
is the
,
(
FN9097.4
ER
(EQ. 3)
(EQ. 4)
)
, is