ISL6217CVZ Intersil, ISL6217CVZ Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
ISL6217CVZ
Manufacturer Part Number
ISL6217CVZ
Description
IC CTRLR PWM INTEL PENT 38-TSSOP
Manufacturer
Intersil
Datasheet
1.ISL6217CVZ.pdf
(19 pages)
Specifications of ISL6217CVZ
Applications
Controller, Intel Pentium® IMVP-IV, IMVP+
Voltage - Input
5.5 ~ 25 V
Number Of Outputs
1
Operating Temperature
-10°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
38-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL6217CVZ
Manufacturer:
Intersil
Quantity:
1 000
Company:
Part Number:
ISL6217CVZ
Manufacturer:
INTERSIL
Quantity:
485
Part Number:
ISL6217CVZ
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL6217CVZ-T
Manufacturer:
INTER
Quantity:
2 500
Company:
Part Number:
ISL6217CVZ-T
Manufacturer:
NS
Quantity:
2 500
FIGURE 3.
The “Droop” current source, I DROOP , is proportional to
load current. This current source is used to reduce the
reference voltage on EA+ by the voltage drop across the
“Droop” resistor. A more in-depth explanation of “Droop”,
and the sizing of this resistor, can be found in the “Droop
Compensation” section of this document.
The choice of value for soft start capacitor is determined by
the maximum slew rate required for the application. An
example calculation is shown below. Using the combined I1
and I2 current sources on the SOFT pin as 130mA, and the
worst case slew rate of (10mV/µs), the SOFT capacitor is
calculated as follows:
Gate-Drive Signals
The ISL6217 provides internal gate-drive for a two channel,
Synchronous Buck, Core Regulator. During two channel
mode of operation, the PWM drive signals are switched
180° out of phase to reduce ripple current delivered from
the DC rail and to the load.
The ISL6217 was designed with a 4 amp, low-side gate
current sinkability, and a 2 amp low-side gate current
source ability, to efficiently drive the latest, high-
performance MOSFETs. This feature will provide the
system designer with flexibility in MOSFET selection, as
well as optimum efficiency during Active mode of operation.
C
SOFT
=
SOFT
SlewRate
I
SOURCE
SOFT-START TRACKING CIRCUITRY SHOWING
INTERNAL CURRENT SOURCES AND "DROOP"
FOR ACTIVE, DEEP AND DEEPER SLEEP
MODES OF OPERATION
C SOFT
=
+ V DROOP
R DROOP
130
I
1
µA
×
I
DROOP
10
1
µs
mV
9
EA+
ISL6217
=
I
. 0
2
013
+
µF
≈
Error
Amplifier
. 0
012
µF
(EQ. 1)
ISL6217
FIGURE 4.
PWRCH pin
A HIGH logic level on this pin enables two channel
operation and a LOW logic signal enables single channel
operation. By tying this pin to the STP_CPU# system
signal, (DSEN# pin on ISL6217) single channel operation
will be invoked during the light loading of both Deep and
Deeper Sleep. If single channel operation is desired only
during Deeper Sleep, the inversion of system signal
DPRSLPVR can be connected to this pin.
The aggressive gate-drive capability of ISL6217, coupled
with the single channel operation feature results in superior
efficiency performance over both light and heavy loads.
Frequency Setting
Both channel switching frequencies are set up by a resistor
from the FSET pin to ground. The choice of FSET
resistance for a desired switching frequency can be
approximated using Figure 4. The switching frequency is
designed to operate between 250kHz and 1MHz per
phase.
CORE Voltage Programming
The voltage identification pins (VID0, VID1, VID2, VID3,
VID4 and VID5) set the DAC output voltage. These pins do
not have internal pull-up or pull-down capability. These pins
will recognize 1.0V, 3.3V, or 5.0V CMOS logic. Table 1
shows the command voltage, V DAC for the 6 bit VID
codes.
The IC responds to VID code changes as shown in
Figure 5. PGOOD is masked between these transitions.
250
200
150
100
50
0
250
Channel Switching Frequency, Fsw,
(
CHANNEL SWITCHING FREQUENCY VS. R FSET
)
500
750
1000