MAX1779EUE+T Maxim Integrated Products, MAX1779EUE+T Datasheet - Page 12
![IC DC-DC CONV TRPL LCD 16-TSSOP](/photos/6/56/65666/175-16-tssop_sml.jpg)
MAX1779EUE+T
Manufacturer Part Number
MAX1779EUE+T
Description
IC DC-DC CONV TRPL LCD 16-TSSOP
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX1779EUE.pdf
(18 pages)
Specifications of MAX1779EUE+T
Applications
Converter, TFT, LCD
Voltage - Input
2.7 ~ 5.5 V
Number Of Outputs
3
Voltage - Output
2.7 ~ 13 V
Operating Temperature
0°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Low-Power Triple-Output TFT LCD DC-DC
Converter
1.125V), the active-low ready signal (RDY) is pulled low
(see Power Ready section).
Power ready is an open-drain output. When the power-
up sequence is properly completed, the MOSFET turns
on and pulls RDY low with a typical 125Ω on-resis-
tance. If a fault is detected, the internal open-drain
MOSFET appears as a high impedance. Connect a
100kΩ pullup resistor between RDY and IN for a logic-
level output.
Once RDY is low, if any output falls below its fault-
detection threshold, then RDY becomes high imped-
ance.
For the reference, the fault threshold is 1.05V. For the
main boost converter, the fault threshold is 88% of its
nominal value (V
pump, the fault threshold is approximately 88% of its
nominal value (V
pump, the fault threshold is 88% of its nominal value
(V
Once an output faults, all outputs later in the power
sequence shut down until the faulted output rises
above its power-up threshold. For example, if the nega-
tive charge-pump output voltage falls below the fault
detection threshold, the main boost converter remains
active while the positive charge pump stops switching
and its output voltage decays, depending on output
capacitance and load. The positive charge-pump out-
put will not power up until the negative charge-pump
output voltage rises above its power-up threshold (see
the Power-Up Sequencing section).
The voltage at REF is nominally 1.25V. The reference
can source up to 50µA with good load regulation (see
Typical Operating Characteristics). Connect a 0.22µF
bypass capacitor between REF and GND.
Inductor selection depends upon the minimum required
inductance value, saturation rating, series resistance,
and size. These factors influence the converter’s effi-
ciency, maximum output load capability, transient
response time, and output voltage ripple. For most
applications, values between 10µH and 33µH work
best with the controller’s switching frequency.
The inductor value depends on the maximum output
load the application must support, input voltage, and
12
FBP
______________________________________________________________________________________
< 1.11V).
FBN
FB
< 1.1V). For the negative charge
< 140mV). For the positive charge
Design Procedure
Main Boost Converter
Voltage Reference
Fault Detection
Inductor Selection
Power Ready
output voltage. With high inductor values, the MAX1779
sources higher output currents, has less output ripple,
and enters continuous-conduction operation with lighter
loads; however, the circuit’s transient response time is
slower. On the other hand, low-value inductors respond
faster to transients, remain in discontinuous-conduction
operation, and typically offer smaller physical size. The
maximum output current an inductor value will support
may be calculated by the following equations:
A. Continuous-conduction: if
then
B. Discontinuous-conduction: if
then
where I
Electrical Characteristics).
The inductor’s saturation current rating should exceed
peak inductor current throughout the normal operating
range. Under fault conditions, the inductor current may
reach up to 600mA (I
Characteristics). However, the MAX1779’s fast current-
limit circuitry allows the use of soft-saturation inductors
while still protecting the IC.
The inductor’s DC resistance significantly affects effi-
ciency due to the power loss in the inductor. The power
loss due to the inductor’s series resistance (P
be approximated by the following equation:
L
≥
1
2
⎛
⎜
⎝
L
1
ƒ
LIM(MIN)
⎞
⎟
⎠
≥
I
I
MAIN MAX
MAIN MAX
⎛
⎜
⎝
2
V
V
IN MIN
⎛
⎜
⎝
P
MAIN
LR
1
ƒ
(
(
(
⎞
⎟
⎠
≅
⎡
⎢
⎢
⎣
= 350mA and ƒ = 250kHz (see the
)
I
⎛
⎜
⎝
MAIN MAX
)
)
⎞
⎟
⎠
I
MAIN
≥
<
2
2
1
2
⎡
⎢
⎢
⎢
⎢
⎢
⎢
⎣
1
⎛
⎜
⎝
(
⎛
⎜
⎝
⎛
⎜
⎝
⎛
⎜
⎝
LIM(MAX)
V
V
V
V
×
V
V
IN
V
IN MIN
IN MIN
IN MIN
MAIN
MAIN
I
MAIN
V
LIM MIN
(
(
(
)
MAIN
(
V
(
MAIN
V
)
MAIN V IN MIN
⎞
⎟
⎠
)
)
⎞
⎟
⎠
⎞
⎟
⎠
I
, see the Electrical
⎞
⎟ ×
⎠
LIM MIN
I
)
LIM MIN
I
2
LIM MIN
2
-
(
-
V
(
IN MIN
R
(
L
(
(
)
⎞
⎟
⎠
)
-
)
I
)
MAIN MAX
)
)
⎤
⎥
⎥
⎦
LR
(
) may
)
⎤
⎥
⎥
⎥
⎥
⎥
⎥
⎦