MAX1779EUE+T Maxim Integrated Products, MAX1779EUE+T Datasheet - Page 14
![IC DC-DC CONV TRPL LCD 16-TSSOP](/photos/6/56/65666/175-16-tssop_sml.jpg)
MAX1779EUE+T
Manufacturer Part Number
MAX1779EUE+T
Description
IC DC-DC CONV TRPL LCD 16-TSSOP
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX1779EUE.pdf
(18 pages)
Specifications of MAX1779EUE+T
Applications
Converter, TFT, LCD
Voltage - Input
2.7 ~ 5.5 V
Number Of Outputs
3
Voltage - Output
2.7 ~ 13 V
Operating Temperature
0°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Low-Power Triple-Output TFT LCD DC-DC
Converter
nated by the internal switch resistance and the diode
impedance. Start with 0.1µF ceramic capacitors.
Smaller values may be used for low-current applica-
tions.
Increasing the output capacitance or decreasing the
ESR reduces the output ripple voltage and the peak-to-
peak transient voltage. Use the following equation to
approximate the required capacitor value:
Use a bypass capacitor with a value equal to or greater
than the flying capacitor. Place the capacitor as close
to the IC as possible. Connect directly to PGND.
Use Schottky diodes with a current rating equal to or
greater than 4 times the average output current, and a
voltage rating at least 1.5 times V
charge pump and V
Carefully printed circuit layout is extremely important to
minimize ground bounce and noise. First, place the
main boost converter output diode and output capacitor
less than 0.2in (5mm) from the LX and PGND pins with
wide traces and no vias. Then place 0.1µF ceramic
bypass capacitors near the charge-pump input pins
(SUPP and SUPN) to the PGND pin. Keep the charge-
pump circuitry as close to the IC as possible, using
wide traces and avoiding vias when possible. Locate
all feedback resistive dividers as close to their respec-
tive feedback pins as possible. The PC board should
feature separate GND and PGND areas connected at
only one point under the IC. To maximize output power
and efficiency and to minimize output power ripple volt-
age, use extra wide power ground traces and solder
the IC’s power ground pin directly to it. Avoid having
sensitive traces near the switching nodes and high-cur-
rent lines.
Refer to the MAX1779 evaluation kit for an example of
proper board layout.
Some applications require multiple charge-pump
stages due to low supply voltages. In order to reduce
the circuit’s size and component count, an unregulated
charge pump may be added onto the LX switching
node. The configuration shown in Figure 4 works well
for most applications. The maximum output current of
the low-power charge pumps depends on the maxi-
14
______________________________________________________________________________________
C
PUMP
PC Board Layout and Grounding
Applications Information
≥ [I
PUMP
SUPN
Charge-Pump Output Capacitor
Charge-Pump Input Capacitor
for the negative charge pump.
/ (125kHz
LX Charge Pump
SUPP
✕
V
RIPPLE
Rectifier Diode
for the positive
)]
mum load current that the LX charge pump can provide
and is limited by the following formula:
where N is the number of stages in the positive low-
power charge pump, and M is the number of stages in
the negative charge pump. Applications requiring more
output current should not use the LX charge pump, so
they will require extra stages on both low-power charge
pumps. The output capacitor of this unregulated
charge pump needs to be stacked on top of the main
output in order to keep the main regulator stable.
Increasing the integrator capacitor may also be
required to compensate for the additional charge-pump
capacitance on the main regulator loop.
The output capacitor of this unregulated charge pump
needs to be stacked on top of the main output in order
to keep the main regulator stable. Increasing the inte-
grator capacitor may also be required to compensate
for the additional charge-pump capacitance on the
main regulator loop.
TRANSISTOR COUNT: 2846
Table 1. Component Suppliers
INDUCTORS
Coilcraft
Coiltronics
Sumida USA
Toko
CAPACITORS
AVX
Kemet
Sanyo
Taiyo Yuden
DIODES
Central
Semiconductor
International
Rectifier
Motorola
Nihon
Zetex
SUPPLIER
I
LXPUMP
= ((N + 1)
847-639-6400
561-241-7876
847-956-0666
847-297-0070
803-946-0690
408-986-0424
619-661-6835
408-573-4150
516-435-1110
310-322-3331
602-303-5454
847-843-7500
516-543-7100
✕
PHONE
I
POS
Chip Information
) + (M + I
NEG
847-639-1469
561-241-9339
847-956-0702
847-699-1194
803-626-3123
408-986-1442
619-661-1055
408-573-4159
516-435-1824
310-322-3332
602-994-6430
847-843-2798
516-864-7630
) ≤ 5mA
FAX