DPA423G Power Integrations, DPA423G Datasheet - Page 16
![IC CONV DC-DC DPA SWITCH 8SMD](/photos/7/32/73216/596-8-smd_sml.jpg)
DPA423G
Manufacturer Part Number
DPA423G
Description
IC CONV DC-DC DPA SWITCH 8SMD
Manufacturer
Power Integrations
Series
DPA-Switch®r
Specifications of DPA423G
Applications
Converter, Power Over Ethernet and Telecom Applications
Voltage - Input
16 ~ 75 V
Number Of Outputs
1
Voltage - Output
220V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SMD Gull Wing
For Use With
596-1195 - KIT REF DES DPA 6.6W DC-DC CONV596-1009 - KIT DESIGN ACCELERATOR DC-DC596-1007 - KIT DESIGN ACCELERATOR POE CONV
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DPA423GN
Manufacturer:
PowerInt
Quantity:
200
Company:
Part Number:
DPA423GN
Manufacturer:
POWER
Quantity:
5 000
Part Number:
DPA423GN
Manufacturer:
POWER
Quantity:
20 000
Company:
Part Number:
DPA423GN-TL
Manufacturer:
POWER
Quantity:
14 500
Company:
Part Number:
DPA423GN-TL
Manufacturer:
Power Integrations
Quantity:
88 094
Part Number:
DPA423GN-TL
Manufacturer:
POWER
Quantity:
20 000
Figure 27. PoE Interface Circuit Using a Bipolar Transistor Pass-Switch and DPA424P.
Rev. S 12/07
controlled pass-switch. By adding this circuitry to the front end
of a DPA converter, a low cost and low component count PoE
powered device (PD) power supply can be implemented.
Figure 27 shows a typical PD solution.
The PoE specifi cation requires the PD to provide three
fundamental functions: discovery, classifi cation, and pass-
switch connection.
When input voltage is applied to the PD, it must present the
correct discovery signature impedance in the voltage range of
2.5 VDC to 10 VDC. This impedance is provided by R51 in
Figure 27.
The second “classifi cation” phase occurs at input voltages
15 VDC to 20 VDC. The PD must draw a specifi ed current to
identify the device class (Class 0 specifi es 0.5 mA to 4 mA).
This is again accomplished by resistor R51.
In the third phase, the bipolar pass-switch (Q51 in Figure 27)
connects the input voltage to the power supply at voltages
above approximately 30 VDC (28 V+VR52). Zener diode VR51
conducts, driving the current through resistor R52 to the base
of Q51. Resistor R53 prevents turn-on under other conditions.
Once the Power supply has started, components D51, D52,
C51 and R54 enhance the base-current drive by coupling
16
(1,2)
(4,5)
(3,6)
(7,8)
Connector
Ethernet
(RJ-45)
DPA422-426
DL4002
DL4002
DL4002
DL4002
DL4002
DL4002
DL4002
DL4002
D101
D102
D103
D104
D105
D106
D107
D108
1% 1/4 W
24.9 kΩ
TIP29C (100 V/1 A)
R51
BAV19
VR51
PoE Interface
28 V
20 kΩ
D51
R52
20 kΩ
or MMBTA06
R53
Q51
BAV19
20 Ω
1 nF
50 V
D52
C51
R54
1 μH 2.5 A
100 V
1 μF
C1
L1
649 kΩ
SMAJ
100 V
VR1
1 μF
150
1%
R1
C2
1
3
4
D
S
T1
CONTROL
X
5
8
7
6
L
DPA-Switch
174 k
R23
1%
13.3 kΩ
DPA424P
F
power from the power supply bias winding.
Once the three start up phases have been successfully
completed, the DPA-Switch is allowed to function as a forward
converter (described in Figure 25 and accompanying text).
Key Application Considerations
DPA-Switch Design Considerations
Power Table
This section provides a description of the assumptions used to
generate the power tables (Tables 1 and 3 through 6) and
explains how to use the information provided by them.
All Power tables: Tables 1 and 3 through 6
•
•
•
10 Ω
2.2 nF
R21
1%
R2
C21
MMBTS3906
U1
C
220 nF
10 Ω
Maximum output power is limited by the device internal
current limit. This is the peak output power which could
become the continuous output power, provided adequate
heat sinking is used.
Data assumes adequate heat sinking to keep the junction
temperature at or below 100 °C and worst case R
T
The use of P and G packages are recommended for device
dissipation equal to or less than 1.5 W only due to package
thermal limitation. For device dissipation above 1.5 W, use
R package.
R22
C4
Si4804
J
Si4804
Q20
Q21
= 100 °C.
Q22
10 kΩ
R23
20CJQ060
VR21
10 kΩ
D31
R22
R21
10 k
1.0 Ω
47 μF
R3
10 V
SL13
15 V
D21
C5
4
7
8
7
BAV19WS
16 μH 4 A
PC357
19WS
4.7 μF
BAV
N1T
D41
20 V
L2
D6
U2
C6
3
6
5
2
10 kΩ
R11
BAV19WS
LM431AIM3
2.2 μF
10 V
C11
VR41
6.8 V
D11
4.7 μF, 35 V
U3
100 μF 5 V
150 Ω
U2
C22-C24
R12
C41
IN4148
100 μF
10 V
D42
C31
68 nF
C13
100 nF
11 Ω
R13
C12
160 Ω
PI-3824-040706
R4
1 kΩ
R14
www.powerint.com
10 kΩ
10 kΩ
R16
R15
1%
1%
1 μF
10 V
C25
20 V, 10 mA
7.5 V, 0.4 A
DS(ON)
5 V, 2.4 A
RTN
at