EL5525IRE-T7 Intersil, EL5525IRE-T7 Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
EL5525IRE-T7
Manufacturer Part Number
EL5525IRE-T7
Description
IC VREF GEN 18CH TFTLCD 38HTSSOP
Manufacturer
Intersil
Datasheet
1.EL5525IREZ.pdf
(10 pages)
Specifications of EL5525IRE-T7
Applications
Converter, TFT, LCD
Voltage - Input
4.5 ~ 16.5 V
Number Of Outputs
18
Voltage - Output
0.5 ~ 14.95 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
38-TSSOP Exposed Pad, 38-eTSSOP, 38-HTSSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
General Description
The EL5525 provides a versatile method of providing the
reference voltages that are used in setting the transfer
characteristics of LCD display panels. The V/T
(Voltage/Transmission) curve of the LCD panel requires that
a correction is applied to make it linear; however, if the panel
is to be used in more than one application, the final curve
may differ for different applications. By using the EL5525,
the V/T curve can be changed to optimize its characteristics
according to the required application of the display product.
Each of the eight reference voltage outputs can be set with a
10-bit resolution. These outputs can be driven to within
50mV of the power rails of the EL5525. As all of the output
buffers are identical, it is also possible to use the EL5525 for
applications other than LCDs where multiple voltage
references are required that can be set to 10 bit accuracy.
Digital Interface
The EL5525 uses a simple 3-wire SPI compliant digital
interface to program the outputs. The EL5525 can support
the clock rate up to 5MHz.
Serial Interface
The EL5525 is programmed through a three-wire serial
interface. The start and stop conditions are defined by the
ENA signal. While the ENA is low, the data on the SDI (serial
data input) pin is shifted into the 16-bit shift register on the
positive edge of the SCLK (serial clock) signal. The MSB
(bit 15) is loaded first and the LSB (bit 0) is loaded last (see
Table 1). After the full 16-bit data has been loaded, the ENA
is pulled high and the addressed output channel is updated.
The SCLK is disabled internally when the ENA is high. The
SCLK must be low before the ENA is pulled low.
To facilitate the system designs that use multiple EL5525
chips, a buffered serial output of the shift register (SDO pin)
is available. Data appears on the SDO pin at the 16th falling
SCLK edge after being applied to the SDI pin.
To control the multiple EL5525 chips from a single three-wire
serial port, just connect the ENA pins and the SCLK pins
Serial Timing Diagram
SDI
SCLK
ENA
t
HE
t
SD
5
t
SE
MSB
B15
t
HD
LOAD MSB FIRST, LSB LAST
B14
T
B13
EL5525
B12-B2
t
r
together, connect the SDO pin to the SDI pin on the next
chip. While the ENA is held low, the 16m-bit data is loaded to
the SDI input of the first chip. The first 16-bit data will go to
the last chip and the last 16-bit data will go to the first chip.
While the ENA is held high, all addressed outputs will be
updated simultaneously.
The Serial Timing Diagram and parameters table show the
timing requirements for three-wire signals.
The serial data has a minimum length of 16 bits, the MSB
(most significant bit) is the first bit in the signal. The bits are
allocated to the following functions (also refer to Table 1).
• Bit 15 is always set to a zero
• Bits 14 through 10 select the channel to be written to, these
• The 10-bit data is on bits 9 through 0. Some examples of
t
are binary coded with channel A = 0, and channel R = 17
data words are shown in Table 3.
w
B1
B15
B14
B13
B12
B10
B11
BIT
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
TABLE 1. CONTROL BITS LOGIC TABLE
t
f
LSB
B0
t
HE
NAME
Test
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
A4
A3
A2
A1
A0
t
SE
Always 0
Channel Address
Channel Address
Channel Address
Channel Address
Channel Address
Data
Data
Data
Data
Data
Data
Data
Data
Data
Data
DESCRIPTION
t
September 21, 2010
FN7393.2