LM2577T-ADJ/NOPB National Semiconductor, LM2577T-ADJ/NOPB Datasheet - Page 16

• Manufacturer Part Number: LM2577T-ADJ/NOPB
• Description: IC REG SIMPLE SWITCHER TO-220-5
• Manufacturer: National Semiconductor
• Series: SIMPLE SWITCHER®r
• Type: Step-Up (Boost), Flyback, Forward Converterr

Specifications of LM2577T-ADJ/NOPB

• Internal Switch(s): Yes
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: 11.4 ~ 12.6 V
• Current - Output: 3A
• Frequency - Switching: 52kHz
• Voltage - Input: 3.5 ~ 40 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Through Hole
• Package / Case: TO-220-5 (Straight Leads)
• Current, Input Bias: 100 nA
• Current, Output: 3 A
• Current, Supply: 25 mA
• Frequency, Oscillator: 52 kHz
• Package Type: TO-220
• Regulation, Line: 20 mV
• Regulation, Load: 20 mV
• Regulator Type: Boost (Step-Up)
• Resistance, Thermal, Junction To Case: 2 °C/W
• Temperature, Operating, Range: -40 to +125 °C
• Transconductance: 3700
• Voltage, Gain: 800 V/V
• Voltage, Input: 3.5 to 40 V
• Dc To Dc Converter Type: Step Up
• Pin Count: 5 +Tab
• Input Voltage: 40V
• Output Voltage: 11.6 to 12.4V
• Switching Freq: 48 TO 56KHz
• Output Current: 3A
• Efficiency: 80%
• Output Type: Adjustable
• Switching Regulator: Yes
• Load Regulation: 50mV
• Line Regulation: 50mV
• Mounting: Through Hole
• Input Voltage (min): 3.5V
• Operating Temperature Classification: Automotive
• For Use With: 551011367-061 - BOARD WEBENCH LM2577,LM2585/87
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device
• Other names: *LM2577T-ADJ; *LM2577T-ADJ/NOPB; LM2577T-ADJ

www.national.com
Application Hints
where V
recovery diodes (typically);
E • T, the product of volts x time that charges the inductor:
I
B. Identify Inductor Value:
If L
on to step C. Otherwise, the inductor value found in step B1
is too low; an appropriate inductor code should be obtained
from the graph as follows:
IND,DC
ditions for which the LM1577/LM2577 output switch
would be operating beyond its switch current rating. The
minimum operating voltage for the LM1577/LM2577 is
3.5V.
From here, proceed to step C.
2. For Adjustable version
Preliminary calculations:
The inductor selection is based on the calculation of the
following three parameters:
D
MIN
1. From Figure 9, identify the inductor code for the
region indicated by the intersection of E • T and I
This code gives the inductor value in microhenries. The
L or H prefix signifies whether the inductor is rated for a
maximum E • T of 90 V • µs (L) or 250 V • µs (H).
2. If D
the minimum inductance needed to ensure the switching
regulator’s stability:
(max)
, the average inductor current under full load;
is smaller than the inductor value found in step B1, go
F
, the maximum switch duty cycle (0 ≤ D ≤ 0.9):
<
= 0.5V for Schottky diodes and 0.8V for fast
0.85, go on to step C. If D ≥ 0.85, then calculate
(Continued)
IND,DC
.
16
1. Find the lowest value inductor that is greater than L
2. Find where E • T intersects this inductor value to determine
if it has an L or H prefix. If E • T intersects both the L and H
regions, select the inductor with an H prefix.
FIGURE 7. LM2577-12 Inductor Selection Guide
FIGURE 8. LM2577-15 Inductor Selection Guide
01146828
01146827
MIN
.