MAX682ESA+ Maxim Integrated Products, MAX682ESA+ Datasheet - Page 6

• Manufacturer Part Number: MAX682ESA+
• Description: IC CHARGE PUMP 5V 8-SOIC
• Manufacturer: Maxim Integrated Products
• Type: Switched Capacitor (Charge Pump)r

Specifications of MAX682ESA+

• Internal Switch(s): Yes
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: 5V
• Current - Output: 250mA
• Frequency - Switching: 200kHz, 1MHz
• Voltage - Input: 2.7 ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Power - Output: 471mW
• Function: Step Up
• Output Voltage: 5.05 V
• Output Current: 250 mA (Min)
• Supply Current: 0.18 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.3V-Input to Regulated 5V-Output
Charge Pumps
The MAX682/MAX683/MAX684 charge pumps provide
a regulated 5V output from a 2.7V to 5.5V input. They
deliver a maximum of 250mA, 100mA, or 50mA load
current, respectively. Designed specifically for com-
pact applications, a complete regulator circuit requires
only three small external capacitors and one resistor.
An externally adjustable switching frequency and inno-
vative control scheme allow the circuit to be optimized
for efficiency, size, or output noise. The devices also
contain a shutdown feature.
The MAX682/MAX683/MAX684 consist of an error
amplifier, a 1.23V bandgap reference, an internal resis-
tive feedback network, an oscillator, high-current MOS-
FET switches, and shutdown and control logic (Figure
1). Figure 2 shows an idealized unregulated charge-
pump voltage doubler. The oscillator runs at a 50%
duty cycle. During one half of the period, the transfer
capacitor (C
other half, the doubler stacks the voltage across C
and the input voltage, and transfers the sum of the two
voltages to the output filter capacitor (C
than simply doubling the input voltage, the
MAX682/MAX683/MAX684 provide a regulated fixed
output voltage (5V) using either skip mode or constant-
frequency mode. Skip mode and constant-frequency
mode are externally selected via the SKIP input pin.
Figure 1. Functional Block Diagram
6
_______________________________________________________________________________________
SHDN
SKIP
IN
X
) charges to the input voltage. During the
SHDN
Detailed Description
CONTROL
LOGIC
OSC
EN
1.23V
SWITCHES
PGND
OUT
). Rather
OUT
CXP
CXN
X
In skip mode (SKIP = low), the error amplifier disables
switching when it detects an output higher than 5V. The
device then skips switching cycles until the output volt-
age drops. Then the error amplifier reactivates the
oscillator. Figure 3 illustrates the regulation scheme.
This regulation method minimizes operating current
because the device does not switch continuously. SKIP
is a logic input and should not remain floating.
When SKIP is high, the charge pump runs continuously
at the selected frequency. Figure 4 shows a block dia-
gram of the device in constant-frequency mode. The
error amplifier controls the charge on C
gate of the N-channel FET. When the output voltage
falls, the gate drive increases, resulting in a larger volt-
age across C
put ripple. Since the device switches continuously, the
Figure 2. Unregulated Voltage Doubler
Figure 3. Skip-Mode Regulation
C
IN
IN
IN
C
IN
S1
S1
X
. This regulation scheme minimizes out-
C
X
Constant-Frequency Mode
S2
OSCILLATOR
C
X
EN
OSC
S2
X
by driving the
Skip Mode
C
OUT
OUT
OUT