LTC3890EGN-1#TRPBF Linear Technology, LTC3890EGN-1#TRPBF Datasheet - Page 16

• Manufacturer Part Number: LTC3890EGN-1#TRPBF
• Description: IC BUCK SYNC ADJ DUAL 28SSOP
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LTC3890EGN-1#TRPBF

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 2
• Voltage - Output: 0.8 ~ 24 V
• Frequency - Switching: 350kHz ~ 535kHz
• Voltage - Input: 4 ~ 60 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output: -
• Power - Output: -

LTC3890-1
APPLICATIONS INFORMATION
Low Value Resistor Current Sensing
A typical sensing circuit using a discrete resistor is shown
in Figure 4a. R
output current.
The current comparator has a maximum threshold
V
sets the peak of the inductor current, yielding a maximum
average output current, I
half the peak-to-peak ripple current, ΔI
sense resistor value, use the equation:
To ensure that the application will deliver full load current
over the full operating temperature range, choose the
minimum value for the Maximum Current Sense Threshold
(V
When using the controller in very low dropout conditions,
the maximum output current level will be reduced due to
the internal compensation required to meet stability cri-
terion for buck regulators operating at greater than 50%
duty factor. A curve is provided in the Typical Performance
Characteristics section to estimate this reduction in peak
inductor current depending upon the operating duty factor.
Inductor DCR Sensing
For applications requiring the highest possible efficiency
at high load currents, the LTC3890-1 is capable of sensing
the voltage drop across the inductor DCR, as shown in
Figure 4b. The DCR of the inductor represents the small
amount of DC resistance of the copper wire, which can be
less than 1mΩ for today’s low value, high current inductors.
In a high current application requiring such an inductor,
power loss through a sense resistor would cost several
points of efficiency compared to inductor DCR sensing.
If the external (R1||R2) • C1 time constant is chosen to be
exactly equal to the L/DCR time constant, the voltage drop
across the external capacitor is equal to the drop across
the inductor DCR multiplied by R2/(R1 + R2). R2 scales the
voltage across the sense terminals for applications where
16
SENSE(MAX)
SENSE(MAX)
R
SENSE
=
. The current comparator threshold voltage
).
V
I
SENSE(MAX)
MAX
SENSE
+
ΔI
is chosen based on the required
2
L
MAX
, equal to the peak value less
L
. To calculate the
the DCR is greater than the target sense resistor value.
To properly dimension the external filter components, the
DCR of the inductor must be known. It can be measured
using a good RLC meter, but the DCR tolerance is not
always the same and varies with temperature; consult
the manufacturers’ data sheets for detailed information.
Using the inductor ripple current value from the Inductor
Value Calculation section, the target sense resistor value is:
To ensure that the application will deliver full load current
over the full operating temperature range, choose the
minimum value for the Maximum Current Sense Threshold
(V
Next, determine the DCR of the inductor. When provided,
use the manufacturer’s maximum value, usually given at
20°C. Increase this value to account for the temperature
coefficient of copper resistance, which is approximately
0.4%/°C. A conservative value for T
To scale the maximum inductor DCR to the desired sense
resistor value (R
C1 is usually selected to be in the range of 0.1μF to 0.47μF .
This forces R1|| R2 to around 2k, reducing error that might
have been caused by the SENSE
The equivalent resistance R1|| R2 is scaled to the room
temperature inductance and maximum DCR:
The sense resistor values are:
SENSE(MAX)
R
R
R1|| R2 =
R1=
SENSE(EQUIV)
D
=
R1|| R2
DCR
R
R
D
SENSE(EQUIV)
(
).
MAX
DCR at 20°C
; R2 =
D
=
), use the divider ratio:
at T
V
I
L(MAX)
SENSE(MAX)
MAX
L
R1• R
1– R
+
)
D
ΔI
D
• C1
2
L
+
pin’s ±1μA current.
L(MAX)
is 100°C.
38901fa