ISL9104AIRUAZ-T Intersil, ISL9104AIRUAZ-T Datasheet - Page 10

• Manufacturer Part Number: ISL9104AIRUAZ-T
• Description: IC CONV SYNC 4.3MHZ 500MA 6-TDFN
• Manufacturer: Intersil
• Type: Step-Down (Buck)r

Specifications of ISL9104AIRUAZ-T

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 0.8 ~ 6 V
• Current - Output: 500mA
• Frequency - Switching: 4.3MHz
• Voltage - Input: 2.7 ~ 6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 6-µTDFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -

The PWM operation is initialized by the clock from the
oscillator. The P-Channel MOSFET is turned on at the
beginning of a PWM cycle and the current in the P-Channel
MOSFET starts ramping up. When the sum of the CSA
output and the compensation slope reaches the control
reference of the current loop, the PWM comparator COMP
sends a signal to the PWM logic to turn off the P-Channel
MOSFET and to turn on the N-Channel MOSFET. The
N-MOSFET remains on till the end of the PWM cycle. Figure 23
shows the typical operating waveforms during the normal PWM
operation. The dotted lines illustrate the sum of the slope
compensation ramp and the CSA output.
The output voltage is regulated by controlling the reference
voltage to the current loop. The bandgap circuit outputs a
0.8V reference voltage to the voltage control loop. The
feedback signal comes from the FB pin. The soft-start block
only affects the operation during the start-up and will be
discussed separately in “Soft-Start” on page 11. The EAMP
is a transconductance amplifier, which converts the voltage
error signal to a current output. The voltage loop is internally
compensated by a RC network. The maximum EAMP
voltage output is precisely clamped to the bandgap voltage.
Skip Mode (PFM Mode)
Under light load condition, ISL9104, ISL9104A automatically
enters a pulse-skipping mode to minimize the switching loss
by reducing the switching frequency. Figure 24 illustrates the
v
EAMP
v
v
CSA
OUT
d
CLOCK
i
FIGURE 23. PWM OPERATION WAVEFORMS
L
V
OUT
I
L
0
10
16 CYCLES
FIGURE 24. SKIP MODE OPERATION WAVEFORMS
20% PEAK CURRENT LIMIT
ISL9104, ISL9104A
1.015*V
OUT_NOMINAL
V
OUT_NOMINAL
skip mode operation. A zero-cross sensing circuit (as shown
in Figure 22) monitors the current flowing through SW node
for zero crossing. When it is detected to cross zero for
16-consecutive cycles, the regulator enters the skip mode.
During the 16-consecutive cycles, the inductor current could
be negative. The counter is reset to zero when the sensed
current flowing through SW node does not cross zero during
any cycle within the 16-consecutive cycles. Once ISL9104,
ISL9104A enters the skip mode, the pulse modulation starts
being controlled by the SKIP comparator shown in Figure 22.
Each pulse cycle is still synchronized by the PWM clock. The
P-Channel MOSFET is turned on at the rising edge of clock
and turned off when its current reaches ~20% of the peak
current limit. As the average inductor current in each cycle is
higher than the average current of the load, the output
voltage rises cycle over cycle. When the output voltage is
sensed to reach 1.5% above its nominal voltage, the
P-Channel MOSFET is turned off immediately and the
inductor current is fully discharged to zero and stays at zero.
The output voltage reduces gradually due to the load current
discharging the output capacitor. When the output voltage
drops to the nominal voltage, the P-Channel MOSFET will
be turned on again, repeating the previous operations.
The regulator resumes normal PWM mode operation when
the output voltage is sensed to drop below 1.5% of its
nominal voltage value.
Enable
The enable (EN) pin allows user to enable or disable the
converter for purposes such as power-up sequencing. With
EN pin pulled to high, the converter is enabled and the
internal reference circuit wakes up first and then the soft
start-up begins. When EN pin is pulled to logic low, the
converter is disabled, both P-Channel MOSFET and
N-Channel MOSFETS are turned off, and the output
capacitor is discharged through internal discharge path.
November 24, 2009
FN6829.4