ACPL-M75L-000E Avago Technologies US Inc., ACPL-M75L-000E Datasheet
ACPL-M75L-000E
Specifications of ACPL-M75L-000E
Related parts for ACPL-M75L-000E
ACPL-M75L-000E Summary of contents
Page 1
... SOIC-5 package. The optocouplers utilize the latest CMOS IC technology to achieve outstanding per- formance with very low power consumption. Basic build- ing blocks of ACPL-M75L are high speed LEDs and CMOS detector ICs. Each detector incorporates an integrated photodiode, a high speed transimpedance amplifier, and a voltage comparator with an output driver ...
Page 2
... Example 1: ACPL-M75L-500E to order product of Small Outline SO-5 package in Tape and Reel packaging in RoHS compliant. Example 2: ACPL-M75L-000E to order product of Small Outline SO-5 package in tube packaging and in RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information 5000 Vrms/ Surface Tape& ...
Page 3
... Package Dimensions ACPL-M75L (JEDEC MO-155 Package) MXXX XXX 4.4 ± 0.1 (0.276 ± 0.008) (0.173 ± 0.004) (0.016 ± 0.002) 3.6 ± 0.1* (0.142 ± 0.004) 0.102 ± 0.102 2.5 ± 0.1 (0.004 ± 0.004) (0.098 ± 0.004) 1.27 BSC (0.050) DIMENSIONS IN MILLIMETERS (INCHES) * MAXIMUM MOLD FLASH ON EACH SIDE IS 0 ...
Page 4
... Notes: The time from 25 °C to peak temperature = 8 minutes max. T smax = 200 °C, T smin = 150 °C Non-halide ux should be used Regulatory Information The ACPL-M75L has been approved by the following organizations: UL Recognized under UL 1577, component recognition program, File E55361. CSA Approved under CSA Component Acceptance Notice #5, File CA88324 ...
Page 5
Insulation and Safety Related Specifications Parameter Symbol Minimum External Air L(I01) Gap (Clearance) Minimum External L(I02) Tracking (Creepage) Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance CTI (Comparative Tracking Index) Isolation Group All Avago Technologies data sheets report the creepage ...
Page 6
Absolute Maximum Ratings Parameter Storage Temperature Ambient Operating Temperature Supply Voltages Output Voltage Average Forward Input Current Average Output Current Lead Solder Temperature Solder Reflow Temperature Profile Recommended Operating Conditions Parameter Ambient Operating Temperature Supply Voltages Input Current (ON) Forward ...
Page 7
Switching Specifications Over recommended temperature (T All typical specifications are at T =+25° Parameter Propagation Delay Time [2] to Logic Low Output Propagation Delay Time [2] to Logic High Output Pulse Width [3] Pulse Width Distortion [4] Propagation ...
Page 8
0.1 0.01 1.2 1.3 1.4 V -FORWARD VOLTAGE-V F Figure 1. Typical input diode forward characteristic -40 - -TEMPERATURE- A Figure 3. Typical ...
Page 9
... Application Information Bypassing and PC Board Layout The ACPL-M75L optocoupler is extremely easy to use. ACPL-M75L provides CMOS logic output due to the high- speed CMOS IC technology used. The external components required for proper operation are the input limiting resistor and the output bypass ca- pacitor. Capacitor values should be between 0.01 µ ...
Page 10
Pulse-width distortion (PWD) results when t differ in value. PWD is defined as the difference between t and t and often PWD determines the maximum PLH PHL data rate capability of a transmission system. PWD can be expressed in percent ...
Page 11
... To limit the amount of current flowing through the LED recom- mended that a 530ohm resistor is connected in series with anode of LED (i.e. Pin 1 for ACPL-M75L input signal. At 3.3V input signal recommended to connect 250Ω resistor in series with anode of LED. The recommended limiting resistors is based on the assumption that the driv- er output impedence is 50Ω ...
Page 12
... Use of typical I = 6mA per datasheet recommendation FH Using any one of the drive circuits in Figures 15-17 with will result in a typical CMR of 10 kV/μs for ACPL- F M75L, as long as the PC board layout practices are fol- lowed. Figure 15 shows a circuit which can be used with V DD1 ...
Page 13
... V DD 74HC00 (OR ANY OPEN-COLLECTOR /OPEN-DRAIN LOGIC GATE) Figure 16. TTL open-collector/open drain gate drive circuit for ACPL-M75L families. R limit SHIELD + Pulse Gen. - Figure 18. Test circuit for common mode transient immunity and typical waveforms. For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © ...