ACPL-072L-500E Avago Technologies US Inc., ACPL-072L-500E Datasheet - Page 6

• Manufacturer Part Number: ACPL-072L-500E
• Description: OPTOCOUPLER 3.3/5V 25MBD 8-SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of ACPL-072L-500E

• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 10mA
• Data Rate: 25MBd
• Propagation Delay High - Low @ If: 23.5ns
• Input Type: Logic
• Output Type: Push-Pull, Totem-Pole
• Mounting Type: Surface Mount
• Maximum Fall Time: 8 ns
• Maximum Rise Time: 9 ns
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Baud Rate: 25 MBps
• Maximum Power Dissipation: 150 mW
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Number Of Elements: 1
• Baud Rate: 25Mbps
• Output Current: 10mA
• Isolation Voltage: 3750Vrms
• Package Type: SOIC
• Operating Temp Range: -40C to 105C
• Power Dissipation: 150mW
• Propagation Delay Time: 40ns
• Pin Count: 8
• Mounting: Surface Mount
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Table 1. IEC/EN/DIN EN 60747-5-2 Insulation Characteristics*
*
** Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulations section IEC/EN/
Note: These optocouplers are suitable for “safe electrical isolation” only within the safety limit data. Maintenance of the safety data shall be ensured
by means of protective circuits.
Note: The surface mount classification is Class A in accordance with CECC 00802.
Table 2. Insulation and Safety Related Specifications
All Avago Technologies data sheets report the creepage and clearance inherent to the optocoupler component itself. These dimensions are needed as
a starting point for the equipment designer when determining the circuit insulation requirements. However, once mounted on a printed circuit board,
minimum creepage and clearance requirements must be met as specified for individual equipment standards. For creepage, the shortest distance
path along the surface of a printed circuit board between the solder fillets of the input and output leads must be considered.
There are recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances.
Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level.
6
Description
Installation classification per DIN VDE 0110/1.89, Table 1
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b**
V
Partial discharge < 5 pC
Input to Output Test Voltage, Method a**
V
Highest Allowable Overvoltage (Transient Overvoltage t
Safety-limiting values – maximum values allowed in the event of a failure,
also see Figure 2.
Insulation Resistance at T
Parameter
Minimum External
Air Gap (Clearance)
Minimum External
Tracking (Creepage)
Minimum Internal Plastic
Gap (Internal Clearance)
Tracking Resistance
(Comparative Tracking Index)
Isolation Group
IORM
IORM
Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
Surface mount classification is class A in accordance with CECCOO802.
DIN EN 60747-5-2, for a detailed description of Method a and Method b partial discharge test profiles.
for rated mains voltage
for rated mains voltage
for rated mains voltage
Case Temperature
Input Current
Output Power
x 1.875=V
x 1.5=V
PR
, Type and Sample Test, t
PR
, 100% Production Test with t
S
, V
≤
≤
≤
IO
150 Vrms
300 Vrms
450 Vrms
= 500 V
Symbol
L(101)
L(102)
CTI
m
=60 sec, Partial discharge < 5 pC
m
ACPL-
>175
772L
0.08
7.1
7.4
IIIa
=1 sec,
Value
ini
ACPL-072L
= 10 sec)
>175
0.08
4.9
4.8
IIIa
Units
mm
mm
mm
V
Symbol
V
V
V
V
T
I
P
R
S, INPUT
S
IORM
PR
PR
IOTM
S, OUTPUT
IO
Conditions
Measured from input terminals to output termi-
nals, shortest distance through air.
Measured from input terminals to output termi-
nals, shortest distance path along body.
Through insulation distance conductor to con-
ductor, usually the straight line distance thickness
between the emitter and detector.
DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE 0110, 1/89, Table 1)
ACPL-772L
Option 060
I – IV
I – IV
I – III
55/105/21
2
630
1181
945
6000
175
230
600
>109
ACPL-072L
Option 060
I – IV
I – III
55/105/21
2
560
1050
840
4000
150
150
600
>109
Units
V
V
V
V
°C
mA
mW
W
peak
peak
peak
peak