HCNW3120 Avago Technologies US Inc., HCNW3120 Datasheet - Page 12
![OPTOCOUPLR IGBT DRV 2.5A 8DIP](/photos/7/66/76621/516-8-dip__w__sml.jpg)
HCNW3120
Manufacturer Part Number
HCNW3120
Description
OPTOCOUPLR IGBT DRV 2.5A 8DIP
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-3120-500E.pdf
(24 pages)
Specifications of HCNW3120
Voltage - Isolation
5000Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
2.5A
Propagation Delay High - Low @ If
300ns @ 7mA ~ 16mA
Current - Dc Forward (if)
25mA
Input Type
DC
Output Type
Gate Driver
Mounting Type
Through Hole
Package / Case
8-DIP (0.400", 10.16mm)
No. Of Channels
1
Isolation Voltage
5kV
Optocoupler Output Type
Gate Drive
Input Current
16mA
Output Voltage
30V
Opto Case Style
DIP
No. Of Pins
8
Propagation Delay Low-high
0.5µs
Common Mode Voltage Vcm
1500V
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
516-1124-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCNW3120
Manufacturer:
AGILENT
Quantity:
3 360
Part Number:
HCNW3120
Manufacturer:
AGILENT
Quantity:
20 000
Company:
Part Number:
HCNW3120-000E
Manufacturer:
POWER
Quantity:
950
Part Number:
HCNW3120-000E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Company:
Part Number:
HCNW3120-300
Manufacturer:
ALLEGRO
Quantity:
5 510
Company:
Part Number:
HCNW3120-300
Manufacturer:
ST
Quantity:
5 510
Company:
Part Number:
HCNW3120-300E
Manufacturer:
AVAGO
Quantity:
20 000
Part Number:
HCNW3120-300E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Part Number:
HCNW3120-500E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Notes:
1. Derate linearly above 70°C free-air temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10 µs, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with I
3. Derate linearly above 70°C free-air temperature at a rate of 4.8 mW/°C.
4. Derate linearly above 70°C free-air temperature at a rate of 5.4 mW/°C. The maximum LED junction tem-perature should not exceed 125°C.
5. Maximum pulse width = 50 µs, maximum duty cycle = 0.5%.
6. In this test V
7. Maximum pulse width = 1 ms, maximum duty cycle = 20%.
8. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 Vrms for 1 second (leakage detec-
9. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 Vrms for 1 second (leakage detec-
10. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 Vrms for 1 second (leakage detec-
11. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
12. The difference between t
13. Pins 1 and 4 need to be connected to LED common.
14. Common mode transient immunity in the high state is the maximum tolerable dV
15. Common mode transient immunity in a low state is the maximum tolerable dV
16. This load condition approximates the gate load of a 1200 V/75A IGBT.
17. Pulse Width Distortion (PWD) is defined as |t
Package Characteristics
Over recommended temperature (T
Parameter
Input-Output Momentary
Withstand Voltage**
Resistance
(Input-Output)
Capacitance
(Input-Output)
LED-to-Case Thermal
Resistance
LED-to-Detector Thermal
Resistance
Detector-to-Case
Thermal Resistance
*All typicals at T
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to your equipment level safety specification or Avago Application Note 1074 entitled “Op-
tocoupler Input-Output Endurance Voltage. ”
12
minimum = 2.0 A. See Applications section for additional details on limiting I
tion current limit, I
tion current limit, I
tion current limit, I
output will remain in the high state (i.e., V
put will remain in a low state (i.e., V
OH
A
= 25°C.
is measured with a dc load current. When driving capacitive loads V
I-O
I-O
I-O
≤ 5 µA).
≤ 5 µA).
≤ 5 µA).
PHL
and t
Symbol
V
R
C
q
q
q
ISO
I-O
LC
LD
DC
I-O
PLH
O
< 1.0 V ).
between any two HCPL-3120 parts under the same test condition.
A
O
= -40 to 100°C) unless otherwise specified.
> 15.0 V ).
Device
HCPL-3120
HCPL-J312
HCNW3120
HCPL-3120
HCPL-J312
HCNW3120
HCPL-3120
HCPL-J312
HCNW3120
PHL
-t
PLH
| for any given device.
Min.
3750
3750
5000
10
10
12
11
Typ.
10
10
0.6
0.8
0.5
467
442
126
12
13
OH
CM
peak.
/dt of the common mode pulse, V
CM
OH
Max.
0.6
will approach V
/dt of the common mode pulse, V
Units
V
Ω
pF
°C/W
°C/W
°C/W
RMS
CC
as I
RH < 50%,
t = 1 min.,
T
V
T
T
f = 1 MHz
Thermocouple
located at center
underside of
package
Test Conditions
A
A
A
I-O
OH
= 25°C
= 25°C
= 100°C
= 500 V
approaches zero amps.
CM
DC
CM
, to assure that the out-
, to assure that the
Fig.
28
Note
8, 11
9, 11
10, 11
11
O
peak