MOC3082M Fairchild Optoelectronics Group, MOC3082M Datasheet - Page 7

• Manufacturer Part Number: MOC3082M
• Description: OPTOCOUPLER TRIAC-OUT ZC 6-DIP
• Manufacturer: Fairchild Optoelectronics Group

Specifications of MOC3082M

• Voltage - Isolation: 7500Vpk
• Number Of Channels: 1
• Voltage - Off State: 800V
• Output Type: AC, Triac, Zero Cross
• Current - Gate Trigger (igt) (max): 10mA
• Current - Hold (ih): 500µA
• Current - Dc Forward (if): 60mA
• Mounting Type: Through Hole
• Package / Case: 6-DIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output / Channel: -
• Other names: MOC3082-M; MOC3082-MQT; MOC3082-MQT; MOC3082QT

©2005 Fairchild Semiconductor Corporation
MOC3081M, MOC3082M, MOC3083M Rev. 1.0.3
Typical circuit for use when hot line switching is required. In this circuit the “hot” side of the line is switched and the
load connected to the cold or neutral side. The load may be connected to either the neutral or hot line.
R
and 5mA for the MOC3083M. The 39 resistor and 0.01µF capacitor are for snubbing of the triac and may or may not
be necessary depending upon the particular triac and load use.
Suggested method of firing two, back-to-back SCR’s with a Fairchild triac driver. Diodes can be 1N4001; resistors,
R1 and R2, are optional 330 .
Note: This optoisolator should not be used to drive a load directly. It is intended to be a trigger device only.
in
is calculated so that I
800V
Vdc
PULSE
INPUT
V
APPLIED VOLTAGE
0 VOLTS
CC
V
CC
WAVEFORM
MERCURY
Figure 9. Static dv/dt Test Circuit
WETTED
RELAY
R
F
in
* For highly inductive loads (power factor < 0.5), change this value to 360 .
R
R
is equal to the rated I
TEST
in
1
2
3
t RC
Figure 11. Hot-Line Switching Application Circuit
MOC3081M
MOC3082M
MOC3083M
1
2
3
Figure 12. Inverse-Parallel SCR Driver Circuit
504 V
MOC3081M
MOC3082M
MOC3083M
C
TEST
Figure 10. Static dv/dt Test Waveform
D.U.T.
D.U.T.
6
5
4
R1
FT
10 k
330
360
D1
of the part, 15mA for the MOC3081M, 10mA for the MOC3082M,
6
5
4
SCOPE
PROBE
X100
360
7
SCR
R2
FKPF12N80
1. The mercury wetted relay provides a high
2. 100x scope probes are used, to allow high
3. The worst-case condition for static dv/dt is
speed repeated pulse to the D.U.T.
speeds and voltages.
established by triggering the D.U.T. with a
normal LED input current, then removing the
current. The variable R
be gradually increased until the D.U.T.
continues to trigger in response to the applied
voltage pulse, even after the LED current has
been removed. The dv/dt is then decreased
until the D.U.T. stops triggering.
measured at this point and recorded.
V max = 800 V
dv/dt =
D2
39*
0.01
0.63 V max
LOAD
SCR
t RC
LOAD
=
HOT
NEUTRAL
240 VAC
240 VAC
504
t RC
TEST
allows the dv/dt to
www.fairchildsemi.com
RC
is