MDLS-40263-C-HT-HV-FSTN-LED3G Varitronix, MDLS-40263-C-HT-HV-FSTN-LED3G Datasheet - Page 22

• Manufacturer Part Number: MDLS-40263-C-HT-HV-FSTN-LED3G
• Description: LCD MOD 40X2 CHAR FSTN GN BKLT
• Manufacturer: Varitronix
• Series: MDL(S)-40263r

Specifications of MDLS-40263-C-HT-HV-FSTN-LED3G

• Display Type: TN - Twisted Nematic
• Display Mode: Transflective
• Number Of Digits/alpha: 16
• Outline L X W X H: 108.00mm x 20.00mm x 12.00mm
• Viewing Area: 89.00mm L x 10.00mm W
• Backlight: LED - Green
• Display Format: 40 x 2
• Character Size: 3.15mm H x 1.85mm W
• Character Format: 5 x 8 Dots
• Voltage - Supply: 5.0V
• Dot Size: 0.33mm W x 0.35mm H
• Interface: Parallel
• Operating Temperature: -20°C ~ 70°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 153-1129

Printing defect
Polarizer defect
Defect Category
Ink pattern or lines jagged
Uneven ink. Ink darker or
lighter
Dilapidation. Mesh with
dilapidation results in leakage
of ink and form dots on the
glass that can’t be removed
with blade.
Date code defect of printed
pattern: wrong pattern, fuzzy
pattern, misalignment
Scratch on transmissive
polarizer
Scratch on reflective polarizer A, B, C
Scratch on transflective
polarizer
Folded line
Mechanical damage
Discoloration
Wrong or reversed polarizer
Polarizer shift or protrude from
the edge of glass
Defect Description
A, B
A, B
A, B
Printed area Not accept any wrong pattern and
A, B
C
A, B, C
A, B
A, B
C
A, B, C
N/A
N/A
Zone
(a)
than 10% or ≦0.15mm.
(b) Reject if thick or thin part is more
than 10% or ≧0.15mm
Reject if darker or lighter than the color of
sample
Spot:
Diameter
D≤0.1mm
0.1<D≤0.2mm
D>0.2mm
misalignment. Not accept any fuzzy
pattern being difficult to identify.
Pls. Refer to limit sample if there is.
Reject if scratch inside VA
Accept if scratch outside VA
Accepted scratch length: < 2.0mm, two
scratches are allowed on reflective side.
Accept if scratch could not be found when
viewing on top of transmissive polarizer.
Unacceptable if scratch observed with
front light.
Not accept on transmissive polarizer.
Invisible fold on transflective or reflective
polarizer is acceptable.
Not accept, i.e. dent or pinhole
Minor dint is acceptable. Serious dent like
pinhole can not be accept.
Any discoloration can not be accept
Not accept
1-Polarizer protruding can not be accept。
2-When polarizer position shift but still
within perimeter sealed area﹐it is rejected
if perimeter seal underneath is partially
covered.
3- When polarizer position shift but still
within perimeter sealed area ﹐it is
accepted if perimeter seal underneath
could be perfectly seen.
Accept if thick or thin part is less
VL-FS-MDLS40263-01 REV.C
(MDLS40263-HT-HV-F-LED03-YG-12-CON)
PAGE 22 OF 25
JUN/2006
Criterion
Acc No.
Any
1
0
D=(A+B)/2
Drawing Specification