DMC-16433N-SEW-B Optrex America Inc, DMC-16433N-SEW-B Datasheet
DMC-16433N-SEW-B
Specifications of DMC-16433N-SEW-B
OP461NSEWB
Related parts for DMC-16433N-SEW-B
DMC-16433N-SEW-B Summary of contents
Page 1
... Optical Specifications ..............................................................................6 4. I/O Terminal.............................................................................................8 5. Test..........................................................................................................10 6. Appearance Standards............................................................................11 7. Code System of Production Lot ..........................................................14 8. Type Number .........................................................................................14 9. Applying Precautions .............................................................................14 10. Handling Precautions .............................................................................15 Rev. Date DMC16433N-SEW-B (BA) No.96-0330 First Edition November 14, 1996 Final Revision ******* Table of Contents Revision History Page OPTREX CORPORATION OPTREX Approved by Production Div ...
Page 2
... Outline Dimensions ： 60g max. Weight ： NSD-7140 LCD Type ： 6:00 Viewing Angle ： Electro Luminescence (EL), Color / White Backlight ： Dimensional Outline Drawings DMC16433N-SEW-B (BA) No.96-0330 ( STN / Neutral-mode / Transflective ) UE-31748B OPTREX CORPORATION OPTREX Page 2/15 ...
Page 3
... High Level V IH Input Voltage Low Level V IL Input Voltage High Level V OH Output Voltage Low Level V OL Output Voltage Supply Current I CC DMC16433N-SEW-B (BA) No.96-0330 Conditions Min. － -0.3 － 0 － -0.3 Conditions Min. － 4.5 Shown in 3.1 V =5.0V±10% 2 =5.0V±10% ...
Page 4
... Enable Pulse Width (High Level) Enable Rise/Fall Time Address Setup Time (RS, R Address Hold Time Data Setup Time Data Hold Time 1 Data Delay Time Data Hold Time 2 RS R/W E DB0 ～ DB7 RS R/W E DB0 ～ DB7 DMC16433N-SEW-B (BA) No.96-0330 Symbol Conditions t Fig.1, 2 CYC PW Fig. Fig. Fig ...
Page 5
... Input Frequency AC 100Vrms 2.4.2.Operating Characteristics Parameter Conditions Input Voltage Input Frequency Current AC 100Vrms, 400Hz Life AC 100Vrms, 400Hz Ta=20℃, 60%RH Recommended Inverter : NEL-D32- 5.0V±10%, Produced by NEC ) DMC16433N-SEW-B (BA) No.96-0330 Min. － 450Hz － Min. － － － － － 2000 OPTREX CORPORATION OPTREX Ta=25℃ ...
Page 6
... ON signal is applied to. Vth2 : The voltage V O-P the segment which the OFF signal is applied to. V O-P × 〈 ON SIGNAL 〉 DMC16433N-SEW-B (BA) No.96-0330 Conditions Ta= 0℃ -V Ta=25℃ Ta=50℃ Ta=25℃, 1/16 Duty, 1/4.5 Bias, V Conditions θ= 0ﾟ, φ=－ﾟ ...
Page 7
... Duty, 1/4.5 Bias ﾟ 135 ﾟ 180 ﾟ 225 ﾟ 270 ﾟ ･Area shows typ. CR≧2 3.4.System Block Diagram Photometer #1980A WB Computer DMC16433N-SEW-B (BA) No.96-0330 f =4.7V, =70Hz ﾟ φ ( φ ﾟ） θ 180 ﾟ 315 ﾟ ...
Page 8
... EL 16 4.2.Example of Power Supply It is recommended to apply a potentiometer for the contrast adjust due to the tolerance of the driving voltage and its temperature dependence. MODULE DMC16433N-SEW-B (BA) No.96-0330 Function Power Supply (0V, GND) Power Supply for Logic Power Supply for LCD Drive Register Select Signal ...
Page 9
... Diagram DB7 8 DB0 E Control LSI RS HD44780UA R/W or equivalent VEE VCC VSS EL EL DMC16433N-SEW-B (BA) No.96-0330 COM 16 16 characters × 4 lines SEG 40 Segment Driver 4 MSM5259 × equivalent EL OPTREX CORPORATION OPTREX SEG 120 Page 9/15 ...
Page 10
... Note 4 : The function test shall be conducted after 4 hours storage at the normal temperature and humidity after removed from the test chamber. Note 5 : Vibration test will be conducted to the product itself without putting container. DMC16433N-SEW-B (BA) No.96-0330 Conditions 50℃±2℃, 96hrs (operation state) 0℃±2℃, 96hrs (operation state) 70℃ ...
Page 11
... All directions for inspecting the sample should be within 45ﾟagainst perpendicular line. 6.2.Definition of applicable Zones A Zone : Active display area B Zone : Area from outside of "A Zone" to validity viewing area C Zone : Rest parts A Zone + B Zone = Validity viewing area DMC16433N-SEW-B (BA) No.96-0330 45 ﾟ A Zone Bezel Flame B Zone C Zone ...
Page 12
... Foreign Substances (2) Line Shape Total defects shall not exceed 5. 2 Air Bubbles (between glass & polarizer) Total defects shall not exceed 3. DMC16433N-SEW-B (BA) No.96-0330 Criteria Zone Dimension (mm) D ≦ 0.1 0.1 ＜ D ≦ 0.2 0.2 ＜ D ≦ 0.3 0.3 ＜ Long + Short ) / 2 ...
Page 13
... Not to be conspicuous defects. 5 Polarizer Dirts If the stains are removed easily from LCDP surface, the module is not defective. 6 Color Variation Not to be conspicuous defects. DMC16433N-SEW-B (BA) No.96-0330 Criteria 0.15 ≧ As per the sketch of left hand. Should not be connected to next dot. X (X+Y) / 2≦0.2mm Y (Less than 0 ...
Page 14
... The type number of module is specified on the back of module as follows : ＤＭＣ１６４３３ Ｎ－ＳＥＷ－Ｂ Etching or Printing 9.Applying Precautions Please contact us when questions and/or new problems not specified in this specifications arise. DMC16433N-SEW-B (BA) No.96-0330 □ □ Factory Number Factory Code (Alphabet) Production Week (1～ ...
Page 15
... Optrex shall not be responsible for any infringement of industrial property rights of third parties in any country arising out of the application or use of Optrex Products, except which directly concern the structure or production of such products. DMC16433N-SEW-B (BA) No.96-0330 (GND) is not specified in the module. SS OPTREX CORPORATION ...