AFCT-5715PZ Avago Technologies US Inc., AFCT-5715PZ Datasheet - Page 9

• Manufacturer Part Number: AFCT-5715PZ
• Description: TXRX OPT SFF PLUGGABLE BAIL DMI
• Manufacturer: Avago Technologies US Inc.
• Series: -r

Specifications of AFCT-5715PZ

• Data Rate: 1.25Gbd
• Wavelength: 1310nm
• Applications: Ethernet
• Voltage - Supply: 3.14 V ~ 3.47 V
• Connector Type: LC Duplex
• Mounting Type: SFP
• Function: SFP Optical Transceivers with Optional DMI for Gigabit Ethernet 1.25 GBd. Intended for premise, public and access networking applications.
• Product: Transceiver
• Maximum Rise Time: 0.26 ns/0.4 ns
• Maximum Fall Time: 0.26 ns/0.4 ns
• Pulse Width Distortion: 0.227 ns (Max)/0.267 ns (Max)
• Operating Supply Voltage: 3.14 V to 3.47 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 10 C
• Package / Case: SFP
• Data Rate Max: 1.25Gbps
• Supply Current: 200mA
• Supply Voltage: 3.3V
• Data Transmission Distance: 10km
• Wavelength Typ: 1.31µm
• Power Rating: 660mW
• Peak Reflow Compatible (260 C): No
• Leaded Process Compatible: No
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: Singlemode Glass
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Table 7. Receiver Optical Characteristics
Notes:
1. BER = 10
2. An average power of -20 dBm with an Extinction Ratio of 9 dB is approximately equivalent to an OMA of 15 μW.
3. These average power values are specified with an Extinction Ratio of 9 dB. The loss-of-signal circuitry responds to valid 8B/10B-encoded peak
Table 6. Transmitter Optical Characteristics
Notes:
1. Class 1 Laser Safety per FDA/CDRH
2. Contributed total jitter is calculated from DJ and RJ measurements using TJ = RJ + DJ. Contributed RJ is calculated for 1x10-12 BER by
3. Eye shall be measured with respect to the mask of the eye using filter defined in IEEE 802.3 section 38.6.5
9
Parameter
Input Optical Power
Receiver Sensitivity
Stressed Receiver Sensitivity
(Optical Average Input Power)
Receiver Electrical 3 dBUpper
Cutoff Frequency
Operating Center Wavelength
Return Loss (minimum)
Loss of Signal - Assert
Loss of Signal - De-Assert
Loss of Signal - Hysteresis
Parameter
Average Optical Output Power
Optical Extinction Ratio
TX Optical Eye Mask Margin
Center Wavelength
Spectral Width - rms
Optical Rise/Fall Time
Relative Intensity Noise
Contributed Total Jitter (Transmitter)
1.25 Gb/s
POUT TX_DISABLE Asserted
to peak input optical power, not average power.
multiplying the RMS jitter (measured on a single rise or fall edge) from the oscilloscope by 14. Per FC-PI (Table 9 - SM jitter output, note 1), the
actual contributed RJ is allowed to increase above its limit if the actual contributed DJ decreases below its limits, as long as the component
output DJ and TJ remain within their specified FC-PI maximum limits with the worst case specified component jitter input.
-12
Symbol
ER
MM
λC
tr, tf
RIN
TJ
POFF
POUT
σ, rms
Symbol
P
P
/C
P
P
P
A
IN
MIN
D
D
- P
A
Minimum
1270
12
-30
0.5
Minimum
-9.5
9
0
1270
-45
Typical
Typical
-3
30
Maximum
1355
260
-120
0.284
227
Maximum
-3
-19
-14.4
1500
1355
-20
Unit
dBm
dB
%
nm
nm
ps
dB/Hz
UI
ps
dBm
Unit
dBm
dBm
dBm
MHz
nm
dB
dBm
dBm
dB
Notes
Note 1
Note 3
20-80%
Note 2
Notes
1, 2
3
3