AFCT-5963NLZ Avago Technologies US Inc., AFCT-5963NLZ Datasheet - Page 10
![TXRX OPT SM SONET OC3/SDH 2X5](/photos/22/52/225255/3762219_sml.jpg)
AFCT-5963NLZ
Manufacturer Part Number
AFCT-5963NLZ
Description
TXRX OPT SM SONET OC3/SDH 2X5
Manufacturer
Avago Technologies US Inc.
Series
METRAKr
Datasheet
1.AFCT-5963TGZ.pdf
(16 pages)
Specifications of AFCT-5963NLZ
Applications
General Purpose
Data Rate
155Mbps
Wavelength
1300nm
Voltage - Supply
3.1 V ~ 3.5 V
Connector Type
LC Duplex
Mounting Type
Through Hole
Data Rate Max
0.155Gbps
Supply Voltage
3.3V
Wavelength Typ
1300nm
Leaded Process Compatible
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Process plug
This transceiver is supplied with a process
plug for protection of the optical port within
the LC connector receptacle. This process plug
prevents contamination during wave solder and
aqueous rinse as well as during handling,
shipping and storage. It is made of a high-
temperature, molded sealing material that can
withstand +85 °C, and a rinse pressure of 110
lbs per square inch.
The process plug should only be used once.
After removing it from the transceiver, it must
not be used again as a process plug; however,
if it has not been contaminated it can be
reused as a dust cover.
Recommended Solder fluxes
S o l d e r
AFCT-5963TLZ/TGZ/ATLZ/ATGZ/NLZ/NGZ should
be water-soluble, organic fluxes. Recommended
solder fluxes include Lonco 3355-11 from
London Chemical West, Inc. of Burbank, CA,
and 100 Flux from Alpha-Metals of Jersey
City, NJ.
Figure 8. Recommended Panel Mounting
10
(0.4 ±0.004)
DIMENSIONS IN MILLIMETERS (INCHES)
1.
2.
10.16 ±0.1
FIGURE DESCRIBES THE RECOMMENDED FRONT PANEL OPENING FOR A LC OR SG SFF TRANSCEIVER.
SFF TRANSCEIVER PLACED AT 15.24 mm (0.6) MIN. SPACING.
(0.56 ±0.004)
14.22 ±0.1
15.24
DETAIL A
(0.6)
f l u x e s
TOP OF PCB
u s e d
15.24
(0.6)
B
(0.039)
(0.62 MAX. 0.59 MIN.)
15.75 MAX. 15.0 MIN.
1
w i t h
A
SECTION B - B
SOLDER POSTS
t h e
Recommended Cleaning/Degreasing Chemicals
Alcohols: methyl, isopropyl, isobutyl.
Aliphatics: hexane, heptane
Other: naphtha.
Do not use partially halogenated hydrocarbons
such as 1,1.1 trichloroethane, ketones such as
MEK, acetone, chloroform, ethyl acetate,
methylene dichloride, phenol, methylene chloride,
or N-methylpyrolldone. Also, Avago Technologies
does not recommend the use of cleaners that
use halogenated hydrocarbons because of their
potential environmental harm.
LC SFF Cleaning Recommendations
In the event of contamination of the optical
ports, the recommended cleaning process is the
use of forced nitrogen.
thought to have remained, the optical ports can
be cleaned using a NTT international Cletop
stick type (diam. 1.25 mm) and HFE7100
cleaning fluid.
B
If contamination is