AFCT-57R5ATPZ Avago Technologies US Inc., AFCT-57R5ATPZ Datasheet - Page 8

• Manufacturer Part Number: AFCT-57R5ATPZ
• Description: TXRX OPT SFP LC 4/2/1GBD LC CONN
• Manufacturer: Avago Technologies US Inc.

Specifications of AFCT-57R5ATPZ

• Data Rate: 4.25Gbps
• Wavelength: 1310nm
• Applications: General Purpose
• Voltage - Supply: 2.97 V ~ 3.63 V
• Connector Type: LC Duplex
• Mounting Type: SFP
• Function: Digital Diagnostic Optical Transceiver, supports high-speed singlemode optical fiber at signaling rates up to 4.25 Gb/s
• Product: Transceiver
• Maximum Rise Time: 0.09 ns/0.15 ns
• Maximum Fall Time: 0.09 ns/0.15 ns
• Pulse Width Distortion: 0.06 ns (Max)/0.061 ns (Max)
• Operating Supply Voltage: 2.97 V to 3.63 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 10 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: Singlemode Glass
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Notes;
1. Absolute Maximum Ratings are those values beyond which damage to the device may occur if these limits are exceeded for other than a short
2. Between Absolute Maximum Ratings and the Recommended Operating Conditions functional performance is not intended, device reliability is not
3. The module supply voltages, V
Table 3. Absolute Maximum Ratings
Parameter
Storage Temperature
Case Operating Temperature
Relative Humidity
Supply Voltage
Low Speed Input Voltage
Table 4. Recommended Operating Conditions
Parameter
Supply Voltage
Data Rate
Tcase
Notes:
1. The Ambient Operating Temperature limitations are based on the Case Operating Temperature limitations and are subject to the host system
2. Recommended Operating Conditions are those values for which functional performance and device reliability is implied.
Table 5. Transceiver Electrical Characteristics
(T
Parameter
AC Electrical Characteristics
Power Supply Noise Rejection (peak-peak)
DC Electrical Characteristics
Module Supply Current
Power Dissipation
Low Speed Outputs:
Low Speed Inputs:
Notes:
1. Filter per SFP specification is required on host board to remove 10 Hz to 2 MHz content.
2. Pulled up externally with a 4.7 k – 10 k resistor on the host board to 3.3 V.
3. Pulled up externally with a 4.7 k – 10 k resistor on the host board to 3.3 V.
8
C
period of time. See Reliability Data Sheet for specific reliability performance.
implied, and damage to the device may occur over an extended period of time.
Transmit Fault (TX_FAULT), Loss of Signal
(RX_LOS), MOD-DEF 2
Transmit Disable (TX_DIS),
MOD-DEF 1, MOD-DEF 2
thermal design.
= -10 C to 85 C, VccT, VccR = 3.3 V
CC
T and V
CC
R must not differ by more than 0.5 V or damage to the device may occur.
Symbol
T
T
RH
Vcc
V
Symbol
Vcc
S
C
IN
10%)
T, R
T, R
PSNR
Symbol
I
P
V
V
V
V
CC
DISS
OH
OL
IH
IL
Minimum
-40
-10
5
-0.5
-0.5
Minimum
2.97
1.0625
-10
Minimum
2.0
2.0
0
Maximum
100
85
85
3.8
Vcc + 0.5
Typical
100
215
Maximum
3.63
4.25
85
Maximum
300 mA @ 70 C
350 mA @ 85 C
1000
VccT,R+0.3
0.8
Vcc
0.8
Unit
C
C
%
V
V
Unit
V
Gb/s
C
mV
mW
V
V
V
V
Unit
Notes
Note 1, 2
Note 1, 2
Note 1
Note 1, 2, 3
Note 1
Notes
Note 2
Note 2
Note 1, 2
Note 1
Note 2
Note 3
Notes