LXMG1626-12-66 Microsemi Analog Mixed Signal Group, LXMG1626-12-66 Datasheet - Page 5
![MOD INVERTER CCFL DUAL 10W 12V](/photos/28/27/282770/lxmg1626-12-66_sml.jpg)
LXMG1626-12-66
Manufacturer Part Number
LXMG1626-12-66
Description
MOD INVERTER CCFL DUAL 10W 12V
Manufacturer
Microsemi Analog Mixed Signal Group
Series
PanelMatch™r
Type
Inverters for CCFL and UV Lampsr
Datasheet
1.LXMG1626-12-66.pdf
(6 pages)
Specifications of LXMG1626-12-66
Voltage - Input
10.8 ~ 13.2V
Output
1800V
Size / Dimension
5.24" L x 0.98" W x 0.30" H (133mm x 25mm x 7.5mm)
Mounting Type
Chassis Mount
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LXMG1626-12-66
Manufacturer:
Microsemi Analog Mixed Signal
Quantity:
135
Copyright © 2005
Rev. 1.0, 2005-11-15
0 < P.W. < 100% of period
TM
500K
DAC or
Pot
Figure 1A – PWM Brightness Control
from System
PWM Signal
5µs to 100µS
(Output current set to maximum)
Figure 2 – Max Output Current
Figure 1 – Brightness Control
BRITE
SLEEP
SET
(SET
H
H
L
L
P.W.
BRITE
SET
1
NC
L=GND; H=Open
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
SLEEP
LXMG1626-12-66
1
1
SET
and SET
H
H
LXMG1626-12-66
L
L
SET
NC
2
V
5V
IN1
V
2
10.0mA
11.5mA
12.8mA
14.0mA
5V
IN1
BRITE
2
LXMG1626-12-66
GND
Inputs)
GND
RMS
RMS
RMS
RMS
V
V
V
V
V
V
HI2
HI1
LO
HI1
HI2
LO
T Y P I C A L A P P L I C A T I O N
Integrated Products
®
Microsemi
PanelMatch™
12V 10W Dual CCFL Programmable Inverter Module
The brightness control may be a voltage output DAC or
other voltage source, a digital pot or 500K manual pot. The
inverter contains an internal 215K pull-up to 3V to bias the
pot. A 3.3V Logic Level PWM signal from a micro-
controller may also be used as shown in Figure 1A.
If you need to turn the inverter ON/OFF remotely, connect
to TTL logic signal to the
Connect V
lamps. Connect V
(wire with thinner insulation).
circuit ground, as this will defeat lamp current regulation.
If both lamp wires have heavy high voltage insulation,
connect the longest wire to V
white.
Use the SET
desired maximum output current. Using these two pins in
combination allows the inverter to match a wide variety of
panels from different manufactures. Generally, the best
lamp lifetime correlates with driving the CCFL at the
manufactures nominal current setting. However, the SET
and SET
current to the maximum allowable output current to
increase panel brightness at the expense of some reduced
lamp life.
Although the SET pins are designed such that just leaving
them open or grounding them is all that is needed to set the
output current, they can also be actively set. Using an open
collector or open drain logic signal will allow you to
reduce the lamp current for situations where greater dim
range is required, as an example in nighttime situations. In
conjunction with a light sensor or other timer the panel
could be set to higher brightness (maximum output
current) for daytime illumination and lower brightness
(minimum or typical output current) at nighttime. Since
the dim ratio is a factor of both the burst duty cycle and the
peak output current, using this technique the effective dim
ratio can be increased greater than the burst duty cycle
alone.
overdrive the lamp temporarily to facilitate faster lamp
warm up at initial lamp turn on. Of course, any possible
degradation on lamp life from such practices is the users
responsibility since not all lamps are designed to be
overdriven.
The inverter has a built in fault timeout function. If both
outputs are open (lamps disconnected or broken) or shorted
to ground the inverter will attempt to strike the lamp for
number of cycles. After about one to two seconds without
success the inverter, will shutdown. In order to restart the
inverter it is necessary to toggle the SLEEP input or cycle
the V
IN1
P
input supply
2
RODUCTION
Conversely, the SET inputs could be used to
inputs allow the user the flexibility to adjust the
HI1
1
and SET
and V
LO
HI2
to the low voltage wire lamp return
2
D
(see Figure 2) inputs to select the
to high voltage wires from the
SLEEP
ATA
LO
S
LXMG1626-12-66
input.
. This wire is typically
HEET
Never connect V
LO
to
Page 5
1