VHB200W-Q48-S12 CUI Inc, VHB200W-Q48-S12 Datasheet - Page 5

• Manufacturer Part Number: VHB200W-Q48-S12
• Description: CONVERTER DC/DC 12V 16.7A 200W
• Manufacturer: CUI Inc
• Series: V-Infinity VHB200Wr
• Type: Isolatedr

Specifications of VHB200W-Q48-S12

• Output: 12V
• Number Of Outputs: 1
• Power (watts): 200W
• Mounting Type: Through Hole
• Voltage - Input: 18 ~ 75V
• Package / Case: 9-DIP Module
• 1st Output: 12 VDC @ 16.7A
• Size / Dimension: 2.40" L x 2.28" W x 0.52" H (61mm x 57.9mm x 13.2mm)
• Power (watts) - Rated: 200W
• Operating Temperature: -40°C ~ 100°C
• Efficiency: 88%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Other names: 102-1992; Q3896225; VHB200W-Q48-S12

PART NUMBER: VHB200W
2. INPUT VOLTAGE RANGE
It is important to ensure the input voltage measured at the converter input pins is within the range for that converter. Make sure wire
losses and voltage ripples are accounted for. One possible problem is driving the converter with a linear unregulated power supply.
For example, if the average voltage measured by a DMM is 9V, with a voltage ripple of 3Vpp, the actual input can swing from 7.5V to
10.5V. This will be outside the specified input range of 10~36V and the converter may not function properly. On the other end, make
sure the actual input voltage does not exceed the highest voltage of 36V or75V.
3. LEAD WIRES
Make sure the input and output wires are of adequate AWG size to minimize voltage drop, and ensure the voltage across the input
terminals is above the converter's rated minimum voltage at all times. It is recommended to have the wire pairs twisted, respectively
for the input pair and the output pair, so as to minimize noise pickup.
4. INPUT CURRENT
The input voltage source must be able to provide enough current to the converter, otherwise it may not start up or operate properly. A
typical symptom is not starting or unusually low output voltage. In general, it is recommended to be able to provide at least:
Ipeak = 150%*Pout/(η η *Vmin) where Pout is the maximum output power, Vmin is the minimum input voltage and η is the converter's
efficiency. As an example, for VHB200W-Q24-S5 to operate with 10~36 V input, 200 W output and an efficiency of 87%, the minimum
source current is recommended to be: Ipeak = 150% * 200 / (87% * 10) = 34.48 A.
5. INPUT FUSE
To limit the input current and to facilitate input reversal protection and input OVP protection, a fast-acting input fuse is recommended
for the input line. The fuse rating will depend on the input range and should allow for the maximum current at the lowest input volt-
age, as shown in this equation: Ipeak = 150%*Pout/(η η *Vmin).
In the previous example of VHB200W-Q24-S5, the peak input current at 10V was calculated to be 34.48 A. A 40 A fuse may be suit-
able for this application. Make sure the fuse voltage rating is higher than the maximum input voltage.
6. REMOTE SENSE
The converter provides regulated outputs at the output terminals. When there is a large current and/or the output cable is of some
length, the voltage at the end of the output cable may be noticeably lower than at the terminals. The converter can compensate up to
0.5V of voltage drop through remote sense terminals. To ensure accurate regulation, run two separate wires (twisted) from the
desired regulation points to the remote sense terminals, as shown below.
20050 SW 112
th
Ave. Tualatin, Oregon 97062
Trim
+Vo
-Vo
+S
-S
FIGURE 2. REMOTE SENSE
phone
phone [phone] fax
DESCRIPTION: half-brick dc-dc converter
fax [phone]
(+)
(-)
Load
page
date
07/2009
5 of 10