NMG0509SC Murata Power Solutions Inc, NMG0509SC Datasheet - Page 3

• Manufacturer Part Number: NMG0509SC
• Description: CONV DC/DC 2W 5VIN 9VOUT SIP
• Manufacturer: Murata Power Solutions Inc
• Series: NMGr
• Type: Isolatedr

Specifications of NMG0509SC

• Output: 9V
• Number Of Outputs: 1
• Power (watts): 2W
• Mounting Type: Through Hole
• Voltage - Input: 4.5 ~ 5.5V
• Package / Case: 7-SIP Module (4 Leads)
• 1st Output: 9 VDC @ 222mA
• Size / Dimension: 0.77" L x 0.30" W x 0.40" H (19.6mm x 7.6mm x 10.2mm)
• Power (watts) - Rated: 2W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 86.5%
• Approvals: UL
• Output Type: Single
• No. Of Output Channels: 1
• Input Voltage: 4.5V To 5.5V
• Power Rating: 2W
• Output Voltage: 9V
• Output Current: 222mA
• Supply Voltage: 5V
• Dc / Dc Converter Case Style: SIP
• Isolation: RoHS Compliant
• Product: Isolated
• Output Power: 2 W
• Input Voltage Range: 4.5 V to 5.5 V
• Input Voltage (nominal): 5 V
• Output Voltage (channel 1): 9 V
• Output Current (channel 1): 222 mA
• Isolation Voltage: 1 KV
• Dc / Dc Converter O/p Type: Single
• No. Of Outputs: 1
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 811-1703-5

APPLICATION NOTES
www.murata-ps.com
Minimum load
The minimum load to meet datasheet specifi cation is 10% of the full rated load across the specifi ed input voltage range. Lower than 10% minimum loading will result in
an increase in output voltage, which may rise to typically double the specifi ed output voltage if the output load falls to less than 5%.
Capacitive loading and start up
Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product
series will start into a capacitance of 47μF with an increased start time, however, the maximum recommended output capacitance is 10μF.
Ripple & Noise Characterisation Method
Differential Mode Noise Test Schematic
All measurement to be taken with the following components connected to the UUT as detailed below. 50 Ohm coax cable, solder connections one end, BNC plug at
the other end.
C1
C2
C3
R1
R2
T1
RLOAD
Measured values are multiplied by 10 to obtain the specifi ed values.
1μF X7R multilayer ceramic capacitor rated at minimum 3 x the output voltage of the UUT
10μF tantalum capacitor rated at minimum 1.5 x the output voltage of the UUT with ESR of less than 100 milliohms at 100 kHz e.g. AVX TPS
series.
100nF multilayer ceramic capacitor, general purpose
450 Ohm resistor, carbon fi lm, ±1%
50 Ohm BNC termination
3T of the coax cable through a ferrite toroid eg Ferroxcube TN32/19/13-3E25
Resistive load at the UUT maximum rating. Connections via twisted wires.
SUPPLY
NMG0505SC
NMG0509SC
NMG0512SC
NMG0515SC
NMG1205SC
NMG1209SC
NMG1212SC
NMG1215SC
DC/DC Converter
Input
+
-
Start-up time
Output
1120
1930
3470
1320
1320
2270
444
409
+
-
μs
C1 C2 C3
R LOAD
R1
Technical enquiries email: [e-mail], tel: [phone]
T1
Isolated 2W Single Output DC/DC Converters
Typical Start-Up Wave Form
R2
OSCILLOSCOPE
Y INPUT
2010/02/12 KDC_NMG.C01 Page 3 of 5
NMG Series