LW020A Lineage Power, LW020A Datasheet
LW020A
Specifications of LW020A
Available stocks
Related parts for LW020A
LW020A Summary of contents
Page 1
Data Sheet April 2008 LW020 Single-Output-Series Power Modules: The LW020 Single-Output-Series Power Modules use advanced, surface-mount technology and deliver high-qual- ity, compact, dc-dc conversion at an economical price. Applications Distributed power architectures n Communication equipment n Computer equipment n Options ...
Page 2
... Refer to the fuse manufacturer’s data for further information. 2 Symbol Min Max 100 I, trans T –40 110 –40 120 stg — — 1500 Symbol Min Typ — — I, max — — I — — — 60 April 2008 Unit Vdc V °C °C Vdc Max Unit 75 Vdc 1 0 — mAp-p — dB Lineage Power ...
Page 3
... LW020G LW020F LW020A LW020B LW020C All All All LW020A LW020B, C LW020A LW020B, C LW020A LW020B LW020C All LW020C LW020B LW020A LW020G LW020F LW020A LW020B LW020C All = 25 °C): A All All All All 36 Vdc to 75 Vdc Inputs Min Typ Max 2.46 2.5 2.54 O, set 3 ...
Page 4
... All V on/off April 2008 Typ Max Unit 0.002 — µF — — M¾ Typ Max Unit 4,500,000 hours — 54 (1.9) g (oz.) Min Typ Max Unit — — 1.0 mA –0.7 — 1.2 V — — — — 50 µA — — 1.2 V Lineage Power ...
Page 5
... All T O rise ) O, nom ; All — O, max LW020B — All others — LW020G V O, clamp LW020F V O, clamp LW020A V O, clamp LW020B V O, clamp LW020C V O, clamp 36 Vdc to 75 Vdc Inputs Min Typ Max Unit — — — 1.5 3 ...
Page 6
... INPUT VOLTAGE, V Figure 1. LW020 Typical Input Characteristics °C A 100 nom O 80 nom O 60 nom 40 nom O 20 nom O 0 50% 100 max NORMALIZED OUTPUT CURRENT, I Figure 2. LW020A and G Typical Output Characteristics ° 0 (V) Figure 3. LW020G Typical Converter Efficiency vs. I 8-1481(C). 0.0 150% , max ...
Page 7
... 75 max O 50% 1.0 1.2 1.4 1 max O (A) O 8-1484(C) Figure 8. LW020A and G Typical Output 36 Vdc to 75 Vdc Inputs 0.2 0.4 0.6 0.8 OUTPUT CURRENT, I (A) O Output Current °C A TIME, t (100 µs/div) Voltage for a Step Load Change from 50% to 75% 1.0 1.2 8-1485(C) 8-1262(C) ...
Page 8
... V , nom O 50 nom O 0 TIME ms/div) Figure 10. LW020A and G Typical Output Voltage Start-Up when Signal Applied to Remote On/Off 8 8 Test Configurations TO OSCILLOSCOPE C 220 µF S IMPEDANCE < 0.1 Ω BATTERY @ 20 ˚C, 100 kHz Note: Input reflected-ripple current is measured with a simulated source impedance of 12 µH. Capacitor Cs offsets possible battery impedance ...
Page 9
... Note: Do not ground either of the input pins of the module without grounding one of the output pins. This may allow a non-SELV voltage to appear between the output pins and ground. Lineage Power 36 Vdc to 75 Vdc Inputs The power module has extra-low voltage (ELV) outputs when all inputs are ELV. ...
Page 10
... Device a b LW020G 14.0 51.10 LW020F 14.0 51.10 LW020A 4.02 16.90 LW020B 15.40 15.40 LW020C 21.50 16.90 The adjusted output voltage cannot exceed 110% of the nominal output voltage between the V minal. The modules have a fixed current-limit set point. Therefore, as the output voltage is adjusted down, the available output power is reduced ...
Page 11
... Therefore, the natural convec- tion condition represents airflow rates 0.3 ms (60 ft./min.). Use of Figure 16 is shown in the following example. Example What is the minimum airflow necessary for a LW020A operating output current of 3.6 A, and a I maximum ambient temperature of 85 °C? ...
Page 12
... OUTPUT CURRENT, I Figure 17. LW020F and G Power Dissipation vs. Output Current ° 0.0 0.5 1.0 1.5 2.0 OUTPUT CURRENT, I Figure 18. LW020A Power Dissipation vs. Output Current 12 12 (continued 0 Figure 19. LW020B Power Dissipation vs. Output 2.9 3.4 3.9 (A) O 8-1478(C).a 4.5 4.0 3 ...
Page 13
... Figure 21. Note that the module and the printed-wiring board (PWB) that it is mounted on are vertically oriented. The passage has a rectangular cross section. Note: Dimensions are in millimeters and (inches) Layout Considerations Copper paths must not be routed beneath the power module standoffs. Lineage Power FACING PWB AIR VELOCITY AND AMBIENT TEMPERATURE MEASURED 76 (3 ...
Page 14
... Tolerances: x.x ± 0.5 mm (0.02 in.), x.xx ± 0.25 mm (0.010 in.). Pin-to-pin tolerances are not cumulative. Note: For standard modules, V (+) is internally connected to the case. I Top View Side View Bottom View 14 April 2008 Pin Function 1 REMOTE ON/OFF 2 No Connec- tion (sync fea- ture optional (– (+) I 5 CASE Pin (pin optional) 6 TRIM 7 V (– (+) O 8-1198(C).g Lineage Power ...
Page 15
... Vdc to 75 Vdc Inputs 12.4 (0.49) 2.54 (0.100) 50.8 (2.00) 7.62 (0.300) 17.78 (0.700) DRILL HOLE OF APPROX. 2.54 (0.100) DIAMETER TO RECESS STANDOFFS IF LOWER HEIGHT IS NEEDED Device Code Comcode LW020G 108258195 LW020F 107640807 LW020A 107314304 LW020B 107681033 LW020C 107640799 8-1198(C).g 15 ...
Page 16
... Lineage Power reserves the right to make changes to the produc t(s) or information contained herein without notice. No liability is ass umed as a res ult of their use or applic ation. No rights under any patent acc ompany the sale of any oduct information. ...