VPOL16A-12-SIP CUI Inc, VPOL16A-12-SIP Datasheet - Page 11
![CONVERTR DC/DC .75/5VOUT 16A SIP](/photos/8/69/86973/mfg_vpol16a-12-sip_sml.jpg)
VPOL16A-12-SIP
Manufacturer Part Number
VPOL16A-12-SIP
Description
CONVERTR DC/DC .75/5VOUT 16A SIP
Manufacturer
CUI Inc
Series
V-Infinity VPOL16Ar
Type
Point of Load (POL) Non-Isolatedr
Datasheet
1.VPOL16A-12-SIP.pdf
(12 pages)
Specifications of VPOL16A-12-SIP
Output
0.75 ~ 5V
Number Of Outputs
1
Power (watts)
80W
Mounting Type
Through Hole
Voltage - Input
9 ~ 14V
Package / Case
11-SIP Module (10 Leads)
1st Output
0.75 ~ 5 VDC @ 16A
Size / Dimension
2.00" L x 0.33" W x 0.51" H (50.8mm x 8.4mm x 13mm)
Power (watts) - Rated
80W
Operating Temperature
-40°C ~ 85°C
Efficiency
94%
Approvals
cUL, UL
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
Other names
102-1293
PART NUMBER: VPOL16A-12-SIP
7.8 VPOL16A-12-SIP Series Output Voltage
Adustment.
The output Voltage of the VPOL16A-12-SIP can be adjusted in the
range 0.75V to 5.0V by connecting a single resistor on the motherboard
(shown as Rtrim) in Figure 13. When Trim resistor is not connected the
output voltage defaults to 0.75V
The value of Rtrim-up defined as:
Where: Rtrim-up is the external resistor in ohm,
To give an exa mple of the above calculation, to set a voltage of 3.3Vdc,
Rtrim is given by:
Rtrim = 3117 ohm
For various output values various resistors are calculated and provided
in Table 3 for co nvenience.
20050 SW 112
Vo is the desired output voltage
+Vin
Common
VPOL16A-12-SIP
Rtrim =
Figure 13. Trim-up Voltage Setup
Rtrim =
Table 3 – Trim Resistor Values
Vo,set (V)
5.0
0.75
1.20
1.50
1.80
2.00
2.50
3.30
th
(
(
Common
3
Ave. Tualatin, Oregon 97062
Vo
3 .
10500
10500
_
_
+Vo
Trim
. 0
. 0
Open
22.33
13.0
9.0
7.4
5.0
3.12
1.47
75
75
Rtrim (Kohm)
_
_
1000
1000
R trim-up
)
)
R-Load
phone
phone 503.612.2300 fax
DESCRIPTION: point of load converter
7.9 Output Ripple and Noise Measurement
The test set-up for noise and ripple measurements is shown in Figure
14. a coaxial cable with a 50ohm termination was used to prevent
impedance mismatch reflections disturbing the noise readings at higher
frequencies.
7.10 Output Capacitance
V-Infinity’s VPOL16A-12-SIP series converters provide unconditional
stability with or without external capacitors. For good transient response
low ESR output capacitors should be located close to the point of load.
For high current applications point has already been made in layout
considerations for low resistance and low inductance tracks.
Output capacitors with its associated ESR values have an impact on
loop stability and bandwidth. V-Infinity’s converters are designed to
work with load capacitance up-to 8,000uF. It is reco mmended that any
additional capacitance, Maximum 8,000uF and low ESR, be connected
close to the point of load and outside the remote compensation point.
7.11 VPOL16A-12-SIP Reflow Profile
An example of the VPOL16A-12-SIP reflow profile is given in Figure 15.
Equipment used: SMD HOT AIR REFLOW HD-350SAR
Alloy: AMQ-M293TA or N C-SMQ92 IND-82088 SN63
Figure 14. Output Voltage Ripple and Noise Measurement Set-Up
240
200
160
120
80
40
+Vin
Common
0
VPOL16A-12-SIP
0
Figure 15 VPOL16A-12-SIP Reflow Profile
30
Common
fax 503.612.2382
+Vo
60
REFLOW PROFILE
TIME (SECONDS)
90
120 150 180 210 240
10uF
Tant.
Ceramic
1uF
rev.
page
date
Test Jack
R-Load
01/2008
11 of 12