DM-COP8/20D National Semiconductor, DM-COP8/20D Datasheet - Page 212
DM-COP8/20D
Manufacturer Part Number
DM-COP8/20D
Description
CABLE FOR DEBUG MODULE 20-DIP
Manufacturer
National Semiconductor
Datasheet
1.DM-COP820D.pdf
(254 pages)
Specifications of DM-COP8/20D
Accessory Type
20-DIP Target Cable
For Use With/related Products
MetaLink Debug Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*DM-COP8/20D
- Current page: 212 of 254
- Download datasheet (2Mb)
Power-on wakeup is a technique used in battery powered applications such as electronic
keys or digital scales to save battery power. Instead of using the HALT mode when the
application is not in use, the microcontroller device is powered off. If there is only one
input switch in the application, the implementation is simple. This switch is put in series
with the battery, providing power to the circuit when the switch is closed.
If there is more than one switch, power-on wakeup can be achieved by using an NPN
transistor and one resistor per switch as shown in Figure 4-8. Here, the circuit ground is
connected to the battery negative terminal via the NPN transistor. If the base is floating,
it will not conduct. If the base is pulled to V
conduct, powering up the circuit.
An alternative technique is shown in Figure 4-9. Here the positive terminal of the
battery is connected to the V
switch is pressed, power is applied to the V
connected to open switches to ground. If the switch is closed, the voltage on the switch
will be V
L pin, the COP device would be driven outside the operating specification. Therefore,
series protection resistors are used on all Port L pins connected to the switches.
4-20
COP8SAx7 APPLICATION IDEAS
CC
plus the diode voltage drop. If this potential were directly applied to the Port
Figure 4-8 Power Wakeup Using An NPN Transistor
CC
Vcc
line via a switch, a diode and two resistors per line. If a
L0
L1
L2
L3
COP8SAx7
CC
GND
Vcc
line. The pull-down resistors pull any ports
CC
via a current-limiting resistor, it will
+
+
Vcc
Related parts for DM-COP8/20D
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
CABLE FOR DEBUG MODULE 28-DIP
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
CABLE FOR DEBUG MODULE 44-PLCC
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPDT BLK
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER DPST 10A QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH PWR ROCKER DPST SNAP-IN
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPST SNAP-IN QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER SPST ILUM 10A/125V
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPDT W/MRK QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER DPST 3A QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER ILLUM 10A GRN
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER DPST SNAP-IN QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER DPST 3A QC
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
MINI ROCKER DPDT BLK
Manufacturer:
C&K Components
Datasheet:
Part Number:
Description:
SWITCH ROCKER POWER SPST 3A QC
Manufacturer:
C&K Components
Datasheet: