EVAL-AD7663CBZ Analog Devices Inc, EVAL-AD7663CBZ Datasheet - Page 6
![BOARD EVALUATION FOR AD7663](/photos/9/11/91111/eval-ad7663cb_board_sml.jpg)
EVAL-AD7663CBZ
Manufacturer Part Number
EVAL-AD7663CBZ
Description
BOARD EVALUATION FOR AD7663
Manufacturer
Analog Devices Inc
Series
PulSAR®r
Specifications of EVAL-AD7663CBZ
Number Of Adc's
1
Number Of Bits
16
Sampling Rate (per Second)
250k
Data Interface
Serial, Parallel
Inputs Per Adc
1 Single Ended
Input Range
±4 REF
Power (typ) @ Conditions
35mW @ 250kSPS
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD7663
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD7663
Pin
No.
1
2
3, 6, 7,
44–48
4
5
8
9, 10
11, 12
13
14
15
16
17
18
19
20
Mnemonic
AGND
AVDD
BYTESWAP
OB/2C
SER/PAR
D[0:1]
D[2:3] or
DIVSCLK[0:1]
D[4]
or EXT/INT
D[5]
or INVSYNC
D[6]
or INVSCLK
D[7]
or RDC/SDIN
OGND
OVDD
DVDD
DGND
NC
Type Description
P
P
DI
DI
DI
DO
DI/O When SER/PAR is LOW, these outputs are used as Bit 2 and Bit 3 of the Parallel Port Data
DI/O When SER/PAR is LOW, this output is used as Bit 4 of the Parallel Port Data Output Bus.
DI/O When SER/PAR is LOW, this output is used as Bit 5 of the Parallel Port Data Output Bus.
DI/O When SER/PAR is LOW, this output is used as Bit 6 of the Parallel Port Data Output Bus.
DI/O When SER/PAR is LOW, this output is used as Bit 7 of the Parallel Port Data Output Bus.
P
P
P
P
Input Analog Power Pin. Nominally 5 V.
Bit 0 and Bit 1 of the Parallel Port Data Output Bus. When SER/PAR is HIGH, these outputs
When SER/PAR is HIGH, EXT/INT is LOW and RDC/SDIN is LOW, which is the Serial
Input/Output Interface Digital Power Ground.
Input/Output Interface Digital Power. Nominally at the same supply as the supply of the host
Digital Power. Nominally at 5 V.
Digital Power Ground.
Analog Power Ground Pin.
No Connect.
Parallel Mode Selection (8/16 Bit). When LOW, the LSB is output on D[7:0] and the MSB is output
on D[15:8]. When HIGH, the LSB is output on D[15:8] and the MSB is output on D[7:0].
Straight Binary/Binary Twos Complement. When OB/2C is HIGH, the digital output is straight
binary; when LOW, the MSB is inverted, resulting in a twos complement output from its internal
shift register.
Serial/Parallel Selection Input. When LOW, the Parallel Port is selected; when HIGH, the
Serial Interface Mode is selected and some bits of the Data bus are used as a Serial Port.
are in high impedance.
Output Bus.
Master Read after Convert Mode. These inputs, part of the Serial Port, are used to slow down,
if desired, the internal serial clock that clocks the data output. In the other serial modes, these
pins are high impedance outputs.
When SER/PAR is HIGH, this input, part of the Serial Port, is used as a digital select input for
choosing the internal or an external data clock, called respectively, Master and Slave Modes.
With EXT/INT tied LOW, the internal clock is selected on SCLK output. With EXT/INT
set to a logic HIGH, output data is synchronized to an external clock signal connected to the
SCLK input, and external clock is gated by CS.
When SER/PAR is HIGH, this input, part of the Serial Port, is used to select the active state of
the SYNC signal. When LOW, SYNC is active HIGH. When HIGH, SYNC is active LOW.
When SER/PAR is HIGH, this input, part of the Serial Port, is used to invert the SCLK signal.
It is active in both master and slave mode.
When SER/PAR is HIGH, this input, part of the Serial Port, is used as either an external data
input or a read mode selection input, depending on the state of EXT/INT.
When EXT/INT is HIGH, RDC/SDIN could be used as a data input to daisy-chain the conversion
results from two or more ADCs onto a single SDOUT line. The digital data level on SDIN is
output on DATA with a delay of 16 SCLK periods after the initiation of the read sequence.
When EXT/INT is LOW, RDC/SDIN is used to select the read mode. When RDC/SDIN is
HIGH, the previous data is output on SDOUT during conversion. When RDC/SDIN is LOW,
the data can be output on SDOUT only when the conversion is complete.
interface (5 V or 3 V).
PIN FUNCTION DESCRIPTION
–6–
REV. B