STEVAL-ISA033V1 STMicroelectronics, STEVAL-ISA033V1 Datasheet - Page 10
![BOARD EVAL L5991/STP12NK80Z](/photos/9/15/91503/steval-isa033v1_sml.jpg)
STEVAL-ISA033V1
Manufacturer Part Number
STEVAL-ISA033V1
Description
BOARD EVAL L5991/STP12NK80Z
Manufacturer
STMicroelectronics
Type
Supervisory Circuitsr
Specifications of STEVAL-ISA033V1
Main Purpose
AC/DC, Primary Side
Outputs And Type
3, Isolated
Power - Output
55W
Voltage - Output
13.8V, 3.8V, 25V
Current - Output
3A, 350mA, 200mA
Voltage - Input
88 ~ 300VAC
Regulator Topology
Flyback
Board Type
Fully Populated
Utilized Ic / Part
L5991, STP12NK80Z
Input Voltage
88 V to 300 V
Output Voltage
3.8 V to 25 V
Product
Power Management Modules
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Frequency - Switching
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
L5991, STP12NK80Z
Other names
497-8226
STEVAL-ISA033V1
STEVAL-ISA033V1
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STEVAL-ISA033V1
Manufacturer:
STMicroelectronics
Quantity:
1
L5991 - L5991A
during ESD tests), it can be connected to VREF
through a 4.7k resistor.
Figure 24. Duty cycle control.
Pin 4. VREF (Reference Voltage). The device is
provided with an accurate voltage reference
(5V 1.5%) able to deliver some mA to an external
circuit.
A small film capacitor (0.1
between this pin and SGND, is recommended to
ensure the stability of the generator and to prevent
noise from affecting the reference.
Before device turn-on, this pin has a sink current ca-
pability of 0.5mA.
Pin 5. VFB (Error Amplifier Inverting Input). The
feedback signal is applied to this pin and is com-
pared to the E/A internal reference (2.5V). The
E/A output generates the control voltage which
fixes the duty cycle.
The E/A features high gain-bandwidth product,
which allows to broaden the bandwidth of the
overall control loop, high slew-rate and current ca-
pability, which improves its large signal behavior.
Usually the compensation network, which stabi-
lizes the overall control loop, is connected be-
tween this pin and COMP (pin 6).
Pin 6. COMP (Error Amplifier Output). Usually,
this pin is used for frequency compensation and
the relevant network is connected between this
pin and VFB (pin 5). Compensation networks to-
wards ground are not possible since the L5991
E/A is a voltage mode amplifier (low output im-
pedance). See application ideas for some exam-
ple of compensation techniques.
It is worth mentioning that the calculation of the
part values of the compensation network must
take the standby frequency operation into ac-
count. In particular, this means that the open-loop
crossover frequency must not exceed f
f
The voltage on pin 6 is monitored in order to re-
10/23
SB
/5.
R
C
A
T
R1
R2
R
B
ST-BY
V
RCT
REF
DC
4
3
16
2
+
-
3 A
F typ.), connected
D97IN727A
TO PWM LOGIC
23K
28K
SB
/4
duce the oscillator frequency when the converter
is lightly loaded (standby).
Pin 7. SS (Soft-Start). At device start-up, a ca-
pacitor (Css) connected between this pin and
SGND (pin 12) is charged by an internal current
generator, ISSC, up to about 7V. During this
ramp, the E/A output is clamped by the voltage
across Css itself and allowed to rise linearly, start-
ing from zero, up to the steady-state value im-
posed by the control loop. The maximum time in-
terval during which the E/A is clamped, referred to
as soft-start time, is approximately:
where R
13) and I
through R
load. Usually, C
der of milliseconds.
As mentioned before, the soft-start intervenes
also in case of severe overload or short circuit on
the output. Referring to fig. 25, pulse-by-pulse
current limitation is somehow effective as long as
Figure 25. Regulation characteristic and re-
the ON-time of the power switch can be reduced
(from A to B). After the minimum ON-time is
reached (from B onwards) the current is out of
control.
To prevent this risk, a comparator trips an over-
current handling procedure, named ’hiccup’ mode
operation, when a voltage above 1.2V (point C) is
detected on current sense input (ISEN, pin 13).
Basically, the IC is turned off and then soft-started
as long as the fault condition is detected. As a re-
sult, the operating point is moved abruptly to D,
creating a foldback effect. Fig. 26 illustrates the
operation.
The oscillation frequency appearing on the soft-
start capacitor in case of permanent fault, referred
to as ’hiccup" period, is approximately given by:
V
T
OUT
ON
D97IN495
D.C.M.
T
T
sense
ss
hic
Qpk
sense
lated quantities.
3 R
is the current sense resistor (see pin
is the switch peak current (flowing
4.5
), which depends on the output
SS
C.C.M.
sense
I
SHORT
I
SSC
is selected for a T
D
I
SSC
1
I
A
OUT(max)
I
Qpk
I
SSD
1
C
B
ss
C
ss
C
SS
(7)
8
in the or-
I
OUT
1-2 ·I
I
I
T
Qpk(max)
Qpk
ON(min)
Qpk