AD9717-EBZ Analog Devices Inc, AD9717-EBZ Datasheet - Page 10
![BOARD EVAL FOR AD9717](/photos/9/16/91604/ad9717-ebz_sml.jpg)
AD9717-EBZ
Manufacturer Part Number
AD9717-EBZ
Description
BOARD EVAL FOR AD9717
Manufacturer
Analog Devices Inc
Series
TxDAC®r
Datasheet
1.AD9717BCPZ.pdf
(80 pages)
Specifications of AD9717-EBZ
Number Of Dac's
2
Number Of Bits
14
Outputs And Type
2, Differential
Sampling Rate (per Second)
125M
Data Interface
Serial
Dac Type
Current
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD9717
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD9714/AD9715/AD9716/AD9717
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Table 7. AD9714 Pin Function Descriptions
Pin No.
1 to 4
5
6
7
8
9
10 to 15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Mnemonic
DB[5:2]
DVDDIO
DVSS
DVDD
DB1
DB0 (LSB)
NC
DCLKIO
CVDD
CLKIN
CVSS
CMLQ
RLQN
QOUTN
QOUTP
RLQP
AVSS
AVDD
RLIP
IOUTP
IOUTN
RLIN
Description
Digital Inputs.
Digital I/O Supply Voltage (1.8 V to 3.3 V Nominal).
Digital Common.
Digital Core Supply Voltage (1.8 V). Strap DVDD to DVDDIO at 1.8 V. If DVDDIO > 1.8 V, bypass DVDD with a
1.0 μF capacitor; however, do not otherwise connect it. The LDO should not drive external loads.
Digital Inputs.
Digital Input (LSB).
No Connect. These pins are not connected to the chip.
Data Input/Output Clock. Clock used to qualify input data.
Sampling Clock Supply Voltage (1.8 V to 3.3 V). CVDD must be ≥ DVDD.
LVCMOS Sampling Clock Input.
Sampling Clock Supply Voltage Common.
Q DAC Output Common-Mode Level. When the internal on chip (QR
the on-chip QR
(QR
resistor (see the Using the Internal Termination Resistors section). The recommended value for this external
resistor is 0 Ω.
Load Resistor (500 Ω) to the CMLQ Pin. For the internal load resistor to be used, this pin should be tied to
QOUTN externally.
Complementary Q DAC Current Output. Full-scale current is sourced when all data bits are 0s.
Q DAC Current Output. Full-scale current is sourced when all data bits are 1s.
Load Resistor (500 Ω) to the CMLQ Pin. For the internal load resistor to be used, this pin should be tied to
QOUTP externally.
Analog Common.
Analog Supply Voltage (1.8 V to 3.3 V).
Load Resistor (500 Ω) to the CMLI Pin. For the internal load resistor to be used, this pin should be tied to
IOUTP externally.
I DAC Current Output. Full-scale current is sourced when all data bits are 1s.
Complementary I DAC Current Output. Full-scale current is sourced when all data bits are 0s.
Load Resistor (500 Ω) to the CMLI Pin. For the internal load resistor to be used, this pin should be tied to
IOUTN externally.
CML
) is disabled, this pin is the common-mode load for Q DAC and must be connected to AVSS through a
CML
DB0 (LSB)
NOTES
1. NC = NO CONNECT
2. THE EXPOSED PAD IS CONNECTED TO AVSS AND
DVDDIO
SHOULD BE SOLDERED TO THE GROUND PLANE.
EXPOSED METAL AT PACKAGE CORNERS IS
CONNECTED TO THIS PAD.
resistor. It is recommended to leave this pin unconnected. When the internal on chip
DVDD
DVSS
DB5
DB4
DB3
DB2
DB1
NC
Figure 2. AD9714 Pin Configuration
10
1
2
3
4
5
6
7
8
9
Rev. A | Page 10 of 80
PIN 1
INDICATOR
(Not to Scale)
AD9714
TOP VIEW
30 RLIN
29 IOUTN
28 IOUTP
27 RLIP
26 AVDD
25 AVSS
24 RLQP
23 QOUTP
22 QOUTN
21 RLQN
CML
) is enabled, this pin is connected to